Cylinder Head Valves
Show/hide table
 | |
| Illustration 1 | g02624516 |
Typical example | |
Show/hide table
| Specification for 350-4386 Cylinder Head Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 4 | 316-5976 Spring | Length under test force is 60.29 mm (2.374 inch). Test force is 460 ± 23 N (103 ± 5 lb). Free length after test is 74.8 mm (2.94 inch). |
| 2 | 4 | 316-5977 Spring | Length under test force is 57.5 mm (2.26 inch). Test force is 248.0 ± 12.4 N (55.8 ± 2.8 lb). Free length after test is 71.4 mm (2.81 inch). |
| 3 | 2 | 316-5980 Valve Stem Seal | Install the valve stem seal to the inlet valves. |
| A | - | - | Height from the top of the cylinder head to the top of the valve guides is 26.0 ± 1.0 mm (1.02 ± 0.04 inch). |
| 4 | 2 | 316-5981 Washer | Install the washer to the exhaust valves. |
| 5 | 2 | 197-6995 Valve Guide | Bore of the exhaust valve guide after installation is 12.619 ± 0.025 mm (0.4968 ± 0.0010 inch). |
| 6 | 2 | 133-9306 Valve Guide | Bore of the inlet valve guide after installation is 9.487 ± 0.025 mm (0.3735 ± 0.0010 inch). |
| 7 | 2 | 194-4897 Exhaust Valve | Before assembly, coat the exhaust valve stems with clean engine oil. Stem diameter is 12.464 ± 0.025 mm (0.4907 ± 0.0010 inch). Face angle is 44.40 ± 0.25 degrees. |
| 8 | 2 | 210-2542 Inlet Valve | Before assembly, coat the inlet valve stems with clean engine oil. Stem diameter is 9.441 ± 0.010 mm (0.3717 ± 0.0004 inch). Face angle is 19.40 ± 0.25 degrees. |
| 9 | 2 | 130-2608 Valve Seat Insert | Diameter of exhaust valve seat insert is 60.119 ± 0.015 mm (2.3669 ± 0.0006 inch). Bore in the cylinder head is 60.508 ± 0.025 mm (2.3822 ± 0.0010 inch). Face angle is 45.00 ± 0.25 degrees. |
| 10 | 2 | 130-2607 Valve Seat Insert | Diameter of inlet valve seat insert is 60.627 ± 0.015 mm (2.3869 ± 0.0006 inch). Bore in the cylinder head is 60.000 ± 0.025 mm (2.3622 ± 0.0010 inch). Face angle is 20.00 ± 0.25 degrees. |
Caterpillar Information System:
C13, C15, and C18 Tier 4 Final Engines Inlet Manifold Air Pressure Sensor
C13, C15, and C18 Tier 4 Final Engines Boost Pressure Sensor
349F and 352F Excavators Machine System Specifications Control Valve (Boom Lowering)
3516B and 3516B High Displacement Engines for 994D and 994F Wheel Loaders Fuel Transfer Pump
C15 and C18 Engines for Caterpillar Built Machines Inlet Air Temperature Sensor
Converting the 165-1594 Harness to the 3E-0020 Converter Control Gp {1408, 1926} Converting the 165-1594 Harness to the 3E-0020 Converter Control Gp {1408, 1926}
C15 Generator Sets Engine Crankcase Breather - Clean
C4.4 Generator Sets Electrical System
C15 Generator Sets Fire Prevention and Explosion Prevention
C4.4 Generator Sets Burn Prevention
C15 Generator Sets General Hazard Information
G3304B and G3306B Engines Fan Drive
C13, C15, and C18 Tier 4 Final Engines Inlet Manifold Temperature Sensor
C3.4B Engines For Caterpillar Built Machines Alternator
Retrofitting for Ultra Lean Burn (ULB) on a G3508 Engine{1000, 775E} Retrofitting for Ultra Lean Burn (ULB) on a G3508 Engine{1000, 775E}
C18 Generator Set Alarms and Shutoffs
3516C Generator Sets Engine Oil and Filter - Change
C18 Generator Set Refill Capacities
C18 Generator Set Coolant Extender (ELC) - Add
C13 Industrial Engine Refill Capacities
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Auxiliary Water Pump
C3.4B Engines For Caterpillar Built Machines Fuel Manifold (Rail)
C3.4B Engines For Caterpillar Built Machines Fuel Filter Base - Secondary Fuel Filter Base
C3.4B Engines For Caterpillar Built Machines Front Housing and Covers