Cylinder Block
Show/hide table
 | |
| Illustration 1 | g03324435 |
Front view | |
Show/hide table
| Specification for 350-5223 Cylinder Block Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 16 | 362-9677 Spacer Plate | During assembly, the bottom of spacer plates must be free of fuel, oil, water, gasket adhesives, assembly compounds, and any other contaminants. Thickness is 12.333 mm (0.4856 inch). |
| 2 | 16 | 144-5692 Plate Gasket | During assembly, both sides of plate gasket must be free of fuel, oil, water, gasket adhesives, assembly compounds and any other contaminants. |
| 3 | 2 | 4W-4813 Plug | Torque to 100 ± 15 N·m (74 ± 11 lb ft). |
| 4 | 1 | 350-1417 Cylinder Block | During assembly, top of cylinder block must be free of fuel, oil, water, gasket adhesives, assembly compounds, and any other contaminants. |
| 5 | 18 | 101-1198 Camshaft Bearing | All centerlines through oil holes in the camshaft bearings and the camshaft bearing junctions must be positioned that is shown in Illustration 1 for each side of the cylinder block. |
| 6 | 8 | 6V-3348 O-Ring Seal | Lubricate the bore lightly with the lubricant that is being sealed. |
| A | 32 | 8T-0099 Dowel | Extension of the dowel from the top face of the cylinder block is 21.0 ± 0.5 mm (0.83 ± 0.02 inch). |
| B | 16 | 197-7008 Dowel | Extension of the dowel from the top face of the cylinder block is 21.0 ± 0.5 mm (0.83 ± 0.02 inch). |
| C | - | - | Bore in the cylinder block for the camshaft bearings is 98.000 ± 0.020 mm (3.8583 ± 0.0008 inch). |
| D | - | - | Oil holes in the camshaft bearings must be positioned from the horizontal centerlines at an angle of 20 ± 5 degrees. Refer to Illustration 1. |
| E | - | - | New dimension from centerline of crankshaft bearing bore to bottom of block (pan rails) is 230.00 mm (9.055 inch). |
| F | - | - | Bore in the block for the main bearings is 169.742 ± 0.020 mm (6.6827 ± 0.0008 inch). |
Show/hide table
 | |
| Illustration 2 | g03324436 |
Right side view | |
Show/hide table
| Item | Qty | Part | Specification Description |
| 7 | 4 | 5F-9657 O-Ring Seal | Lubricate the bore lightly with 5P-3975 Rubber Lubricant. |
| G | 3 | 7N-2047 Dowel | Extension of the dowel from the front face of the cylinder block is 6.0 ± 0.5 mm (0.24 ± 0.02 inch). |
| H | 2 | 4N-0683 Dowel | Extension of dowels from the rear face of the cylinder block is 19.0 ± 0.5 mm (0.75 ± 0.02 inch). |
| J | 2 | 7N-2044 Dowel | Extension of dowels from the front face of the cylinder block is 40.0 ± 0.5 mm (1.57 ± 0.02 inch). |
Show/hide table
 | |
| Illustration 3 | g03324437 |
Show/hide table
| Item | Qty | Part | Specification Description |
| 8 | 16 | 352-6061 Liner Seal | Assemble liner seals dry on clean and dry liner grooves. Before assembly, cover seals with either P-80 Rubber Lubricant Emulsion or liquid soap. |
| 9 | 48 | 7N-2046 O-Ring Seal | Before assembly, cover seals with either P-80 Rubber Lubricant Emulsion or liquid soap. |
| 10 | 9 | 223-1696 Crankshaft Bearing Cap | Width of the crankshaft bearing cap is 340.030 ± 0.015 mm (13.3870 ± 0.0006 inch). |
| 11 | 36 | 7X-7925 Bolt | Use the following procedure in order to tighten the crankshaft bearing cap bolts: Install main bearing caps with the cast part number and FRONT toward the front of the block. Each cap has a number. Each cap must be installed in the same position as the correct number on the side of the cylinder block pan rail. 1. Before assembly, lubricate the threads completely with clean engine oil. 2. Hand tighten bolts in the tapped holes. 3. Tighten bolts in the numerical sequence as shown in Illustration 3 to 190 ± 14 N·m (140 ± 10 lb ft). 4. Again, tighten each bolt to an additional angle of 180 ± 5 degrees. |
| K | - | - | Width in the cylinder block for crankshaft bearing cap is 339.985 ± 0.015 mm (13.3852 ± 0.0006 inch). |
| L | - | - | New dimension from centerline of crankshaft bearing bore to the top of the block is 586.00 mm (23.071 inch). |
Caterpillar Information System:
C13, C15, and C18 Tier 4 Final Engines Speed/Timing Sensor
3516B and 3516B High Displacement Engines for 994D and 994F Wheel Loaders Cylinder Head
C4.4 Industrial Engine Exhaust Cooler (NRS) - Remove and Install - Top mounted Turbocharger
C4.4 Industrial Engine Exhaust Cooler (NRS) - Remove and Install - Side mounted Turbocharger
C4.4 Industrial Engine Exhaust Cooler (NRS) - Remove and Install - Twin Turbocharger
3516C Generator Sets Refill Capacities
C32 Marine Generator Set Safety Messages
3516C Generator Sets Product Lifting
C175-16 Marine Propulsion Engines Engine Overspeed Verification Test
349F and 352F Excavators Machine System Specifications Front Lines - Medium Pressure
3516C Generator Sets Plate Locations and Film Locations
2011/07/01 A New Clamp Is Used on the Exhaust Manifold for G3500C and G3500E Generator Set Engines {1059, 7553}
3512C Oil Well Service Engines Crankshaft Vibration Damper - Inspect
3516C Generator Sets Fluid Recommendations
3516C Generator Sets Product Description
C4.4 Generator Sets Battery Information
3406C Industrial Engine Belts - Inspect/Adjust/Replace
G3304B and G3306B Engines Fan Drive
C15 Generator Sets General Hazard Information
C4.4 Generator Sets Burn Prevention
C15 Generator Sets Fire Prevention and Explosion Prevention
C4.4 Generator Sets Electrical System
C15 Generator Sets Engine Crankcase Breather - Clean
Converting the 165-1594 Harness to the 3E-0020 Converter Control Gp {1408, 1926} Converting the 165-1594 Harness to the 3E-0020 Converter Control Gp {1408, 1926}