UPS Characteristics
一般特征
Show/hide table
| UPS kVA 额定值 | 160 | 200 | 250 | 300 | 400 | 500 |
| 正常交流电输出 | ||||||
| 导线数 | 三相 | |||||
| Pn 下的参考电压 | 380 到 415 V | |||||
| 参考频率 | 45 Hz 到 66 Hz | |||||
| THDI | 在 Pn 下通常 3% | |||||
| 功率因子 | 高于 0.99 | |||||
| 旁路交流电输入 | ||||||
| 导线数 | 三相 + 中线 | |||||
| Pn 下的参考电压 | 380 到 415 V | |||||
| 参考频率 | 45 Hz 到 66 Hz | |||||
| 负载输出 | ||||||
| 导线数 | 三相 + 中线 | |||||
| 设定相间电压 | 380 V / 400 V / 415 V | |||||
| 设定相电压 | 220 V / 230 V / 240 V | |||||
| 电压变化 | ± 1% | |||||
| 可调频率和公差（蓄电池供电） | 50 Hz 或 60 Hz ± 0.1 Hz | |||||
| 0 至 100% 负载阶跃冲击的电压变化 | ± 1% | |||||
| 容许过载 | 150% 30 秒，125% 10 分钟 | |||||
| THDU非线性负载的相间电压和相电压 | 低于 2％相间电压 | |||||
Show/hide table
| 蓄电池 | ||||||||||||
| 标准蓄电池技术 | 密封式铅酸蓄电池（气体重组）（阀控式铅酸型） | |||||||||||
| UPS | ||||||||||||
| 储存温度范围 | −25° C (−13° F) 到 45° C (113° F) |
|||||||||||
| Pn 下的操作温度范围 | 0° C (32° F) 到 35° C (95° F) |
|||||||||||
| 相对湿度 | 45% 到 75% | |||||||||||
| 未降额的最大作业高度 | 低于 1000 m | |||||||||||
| 噪声等级 （dBa） | 75 | |||||||||||
| 产品标准 | IEC 62040 | |||||||||||
| 安全标准 | IEC 62040-1-2 | |||||||||||
| 防护标准 | IEC 62040-3 | |||||||||||
| EMC 标准 | IEC 62040-2 | |||||||||||
| UPS kVA 额定值 | 160 | 200 | 250 | 300 | 400 | 500 | ||||||
| 有效功率（kW） | PN/2 | PN | PN/2 | PN | PN/2 | PN | PN/2 | PN | PN/2 | PN | PN/2 | PN |
| 72 | 144 | 90 | 180 | 112 | 225 | 135 | 270 | 180 | 360 | 225 | 450 | |
| 效率 | 92.0 | 93.2 | 93.0 | 93.0 | 93.2 | 93.8 | 93.5 | 93.6 | 94.1 | 94.1 | 94.3 | 94.3 |
| 热损失（kW） | 6.3 | 10.5 | 6.8 | 13.5 | 8.2 | 14.9 | 9.4 | 18.6 | 11.3 | 22.6 | 13.6 | 27.2 |
| 热损失（cal/s） | 1496 | 2511 | 1619 | 3238 | 1962 | 3554 | 2243 | 4449 | 2697 | 5395 | 3250 | 6501 |
蓄电池特征
Show/hide table
| 密封式铅酸蓄电池 | 开放式铅酸蓄电池 | Ni-Cd 蓄电池 | |
| 电池最小/最大数目 | 264/288 | 264/288 | 428/468 |
| 每个电池的浮动电压 | 2.27 V | 2.2 V | 1.4 V |
| 最低/最高浮动电压 | 600V/654V | 581V/634V | 600V/655V |
| 每个电池的最低电压 | 1.65 至 1.9 V | 1.65 至 1.9 V | 最小阈值 1.1 V |
Caterpillar Information System:
G3304B and G3306B Engines Configuration Parameters
C15 and C18 Petroleum Generator Sets Configuration Parameters
G3304B and G3306B Engines Sensors and Electrical Components
UPSB505 Uninterruptible Power Supply Mimic Panel Indicator
UPSB505 Uninterruptible Power Supply Life Cycle Monitoring
C15 Petroleum Engines Belt Tensioner - Remove and Install
C15 and C18 Petroleum Generator Sets Reference Information
UPSB505 Uninterruptible Power Supply Time and Date Adjustment
G3304B and G3306B Engines Starting the Engine
UPSB125 Uninterruptible Power Supply Fire Prevention and Explosion Prevention
UPSB125 Uninterruptible Power Supply Safety Signs and Labels
UPSB130 Uninterruptible Power Supply UPS Battery - 60Hz Component Location
C27 Generator Set Generator Operation
C3.4B Industrial Engine Monitoring System - Table for the Indicator lamps
C27 Generator Set Hoses and Clamps - Inspect/Replace
C4.4 Industrial Engine Exhaust Elbow - Remove and Install - Top Mounted and Side Mounted Turbocharger Exhaust Elbow
3116 and 3126 Marine Engines Coolant - Change
G3500J Engines Refill Capacities
C15 Petroleum Engines Electronic Control Module - Remove and Install
C3.4B Industrial Engine Sensors and Electrical Components - Aftertreatment
XQ60 Rental Generator Set Sensors and Electrical Components
C15 and C18 Petroleum Generator Sets Refill Capacities
G3516 Petroleum Engine Control Panel - Inspect/Test
G3304B and G3306B Engines Before Starting Engine