Retarder - Install
Installation Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 138-7575 | Link Bracket | 3 |
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install studs (6) to Dimension (X). Dimension (X) is 145.5 ± 0.5 mm (5.73 ± 0.02 inch).
Show/hide table
 | |
| Illustration 1 | g01846054 |
Show/hide table
 | |
| Illustration 2 | g01846453 |
- Install seal (5) .
- Use Tooling (A) and a suitable lifting device in order to install retarder (4). The weight of retarder (4) is approximately 40 kg (88 lb).
Show/hide table
 | |
| Illustration 3 | g01845434 |
- Install thrust bearing (3). Install bearing (2). Install seal rings (1) .
End By: Install the torque converter housing. Refer to Disassembly and Assembly, "Torque Converter Housing - Install".
Caterpillar Information System:
3516C Locomotive Engines Flywheel Housing - Install
CX31 On-Highway Transmission Retarder - Remove
3516C Locomotive Engines Flywheel Housing - Remove
Replacing the Fuel Injection Pump on Certain C9.3 Engines {1251, 1290} Replacing the Fuel Injection Pump on Certain C9.3 Engines {1251, 1290}
3508C, 3512C and 3516C Locomotive Engines Engine Oil Lines
C7 Marine Engine Injector Bolt Torque - Inspect
Troubleshooting the Hydraulic Electronic Unit Injection (HEUI) Fuel System On C7 and C9 Engines{1250} Troubleshooting the Hydraulic Electronic Unit Injection (HEUI) Fuel System On C7 and C9 Engines{1250}
A New Aftercooler Is Used on Certain C9 Marine Engines {1063} A New Aftercooler Is Used on Certain C9 Marine Engines {1063}
Procedures to Salvage Thrust Faces on Planetary Carriers {3160, 4050, 4051, 4093} Procedures to Salvage Thrust Faces on Planetary Carriers {3160, 4050, 4051, 4093}
336F MHPU Mobile Hydraulic Power Unit Machine System Specifications Air Cleaner - Mounting
Equipment and Tools for Undercarriage Rebuilding and Reconditioning Stations {0729, 4150} Equipment and Tools for Undercarriage Rebuilding and Reconditioning Stations {0729, 4150}
349F and 352F Excavators Machine System Specifications Swing Gear and Bearing
Training Materials {0314, 0374, 4150} Training Materials {0314, 0374, 4150}
349F and 352F Excavators Machine System Specifications Check Valve
349F and 352F Excavators Machine System Specifications Relief Valve (Main)
349F and 352F Excavators Machine System Specifications Accumulator (Pilot)
3500 Engines Engine Oil Sequence Valves - Remove and Install
2011/01/10 A New Waste Gate for the Turbocharger Is Now Being Used on the Certain C13 Industrial Engines {1052, 1053, 1057, 1940}
Contamination Control of Rebuilt Engines by Using a Particle Counting Process Patent Pending{1000, 1300} Contamination Control of Rebuilt Engines by Using a Particle Counting Process Patent Pending{1000, 1300}
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators Grade Control Configuration
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators Machine Monitoring System Configuration
C7 Engines for Combat and Tactical Vehicles Grounding Stud - Inspect/Clean/Tighten
349F and 352F Excavators Hydraulic System Relief Valve (Counterweight Cylinder) - Test and Adjust
C7 Engines for Combat and Tactical Vehicles Severe Service Application