Air Conditioning E45 - Air Inlet Damper Error
Show/hide table
| |
| Illustration 1 | g02372561 |
|
(1) Air inlet motor
(2) Air inlet dampers (T) Connector | |
Show/hide table
| |
| Illustration 2 | g02372676 |
|
(3) Air inlet select switch (Recirculated/Fresh air)
(4) Control panel | |
Show/hide table
| |
| Illustration 3 | g02521058 |
|
Partial Electrical Schematic (A) Connector (B) Connector (C) Connector (CC) Connector (D) Connector (DD) Connector (T) Connector (1) Air inlet motor (4) Control panel | |
- Select air inlet select switch (3) on control panel (4).
- Check for movement of air inlet motor (1). If the motor moves, even a little, see Step 3. If the motor does not move, see Step 6.
- If the error is shown after the initial action has finished, see Step 4. If the error is not shown after the initial action has finished, the outlet air damper is locked or there is a problem with the linkage.
- Disconnect connector (T) from the air inlet motor connector. Measure the resistance value between the "BU/BK" wire and the "BR/RD" wire of the air inlet motor connector. The resistance should be approximately 4.7k ohms. If the resistance value is correct, see Step 5. If the resistance value is incorrect, the air outlet motor is defective.
- Check for continuity between the "BU/BK" wire and the "YL/BK" wire, and between the "YL/BK" wire and the "BR/RD" wire of the air inlet motor connector. If there is continuity between the two sets of wires, the control panel is defective. If there is not continuity between the two sets of wires, the air outlet motor is defective.
- If the error is shown, see Step 7. If the error is not shown, replace control panel (4).
- Check the wiring harnesses between the air outlet motor and the control panel for continuity. If there is continuity, either the air outlet motor is defective, the air outlet damper is locked, or there is a problem with the linkage. If there is not continuity, the harness is defective.
Resistance ... 4.7k Ohm
Voltage between connectors ... 5 VDC
Show/hide table
| |
| Illustration 4 | g02350723 |
Caterpillar Information System:
C9 On-highway Engines Severe Service Application
Welding Wire and Flux {0679, 4150, 7950} Welding Wire and Flux {0679, 4150, 7950}
C9 On-highway Engines Fluid Recommendations
Carrier Roller Oil Fill Volume {4154} Carrier Roller Oil Fill Volume {4154}
G3500 A3 Engines Engine Speed Switch
C3.4B Engines Diesel Particulate Filter Active Regeneration Occurrence Is Excessive
Receiving and Unpacking of UPSB220{4480} Receiving and Unpacking of UPSB220{4480}
UPSB220 Uninterruptible Power Supply Computer Network
C9 On-highway Engines Grounding Stud - Inspect/Clean/Tighten
C18 Industrial Engines Grounding Stud - Inspect/Clean/Tighten
UPSB220 Uninterruptible Power Supply Fire Prevention and Explosion Prevention
C13 Engines Engine Speed/Timing Sensor - Clean/Inspect
320 VH and VM Variable Gauge Undercarriage Travel Motor - Disassemble
2011/01/06 A New Valve Bridge Is Available for Certain Commercial Engines {1121}
2011/01/20 A New Valve Bridge Is Available for Certain Machines {1121}
C-12 Engine Compression Brake - Inspect/Adjust/Replace
C-12 Engine Grounding Stud - Inspect/Clean/Tighten
320 VH and VM Variable Gauge Undercarriage Travel Motor - Assemble
2011/01/06 A New Exhaust Plug Is Used on Certain C18 Engines {1058, 1061}
C7 Marine Engine Product Description
C7 Marine Engine Coolant (DEAC) - Change
C7 Marine Engine Coolant (ELC) - Change
CX31 On-Highway Transmission Transmission Planetary - Disassemble
CX31 On-Highway Transmission Transmission Planetary - Assemble