Reference: Refer to Testing and Adjusting, "Work Tool Parameter - Program" for additional programming instructions and parameter descriptions.
Pump Flow Control Mode (Parameter #6)
Set the pump to supply oil flow to the work tool using the following parameter settings for the work tool.
Pump #1 - Drive Pump
Pump #2 - Idler Pump
Combined Flow - Both Pumps
- Select Pump #1 or Pump #2.
- "ATT Valve #1" (Parameter #27 through #36) are now available for setting.
- "ATT Valve #2" (Parameter #37 through #45) are set by parameters used for "ATT Valve #1" for one pump setting.
- Pump #1 is recommended when multiple operation of work tool along with swing or stick function are frequently used.
- Pump #2 is recommended when multiple operation of work tool along with bucket or boom function are frequently used.
- Select Combined Flow.
- (Parameter #27 through #45) are now available for setting.
Pump Flow to the Work Tool (Single Operation)
One Pump Flow using Drive or Idler Pump
- Set the appropriate flow for the work tool to be installed by using the following parameter settings.
"Atch #X Flow Setting" (Parameter # 27) - XXX [L/min]
Show/hide tableTable 1 Maximum Flow Setting for One Pump Flow 349E / 349F 385 L/min (101.7 US gal/min) 336E / 336F 289 L/min (76.3 US gal/min) 329E / 329F / 330F 247 L/min (65.3 US gal/min) 326F 231 L/min (61.0 US gal/min) 324E 231 L/min (61.0 US gal/min) 323E / 320E / 320E N / 323 E N / 320E RR 214 L/min (56.5 US gal/min) 320F / 323F N 211 L/min (55.7 US gpm) 323F 209 L/min (55.2 US gpm) 318E / 316E / 318F / 316F 150 L/min (39.6 US gal/min) 314E CR / 314F / 315F 128 L/min (33.8 US gal/min) 312E / 312F / 313F 128 L/min (33.8 US gal/min) - Work tool open and close speed can be decreased by lowering the following parameter value.
- Spool shift pressure adjustment to extend the attachment control valve.
"Atch #X Max Ext Press" (Parameter #30 and #40) - XXXX [kPa]
Note: For reference, this parameter is set within the range of 800 kPa to 2000 kPa.
- Spool shift pressure adjustment to extend the attachment control valve.
- Set the appropriate flow for the work tool to be installed by using the following parameter settings.
"Atch #1 Flow Setting" (Parameter # 27) - XXX [L/min]
Show/hide tableTable 2 Maximum Flow Setting for Two Pump Flow 349E / 349F 770 L/min (203.4 US gal/min) 336E / 336F 578 L/min (152.7 US gal/min) 329E / 329F / 330F 494 L/min (130.5 US gal/min) 326F 462 L/min (122.0 US gal/min) 324E 462 L/min (122.0 US gal/min) 323E / 320E / 320E N / 323 E N / 320E RR 428 L/min (113.1 US gal/min) 320F / 323F N 422 L/min (111.5 US gpm) 323F 418 L/min (110.4 US gpm) 318E / 316E / 318F / 316F 300 L/min (79.3 US gal/min) 314E CR / 314F / 315F 256 L/min (67.6 US gal/min) 312E / 312F / 313F 256 L/min (67.6 US gal/min) - Work tool open and close speed can be decreased by lowering the following parameter value.
- Spool shift pressure adjustment to extend the attachment control valves.
"Atch #1 Max Ext Press" (Parameter #30) - XXXX [kPa]
"Atch #2 Max Ext Press" (Parameter #40) - XXXX [kPa]
Note: For reference, this parameter is set within the range of 800 kPa to 2000 kPa. A parameter setting for spool shift pressure of 0 kPa is not made for flow from two pumps.
- Spool shift pressure adjustment to extend the attachment control valves.
Pump Flow to the Work Tool (Multiple Operation)
- Set the additional flow to the work tool when multiple operations are to take place by using the following parameter settings.
"Atch #1 Mult-Ope Add Flow Setting" (Parameter # 28) - XXX [L/min]
Note: Pump flow to the work tool may exceed the upper limit flow set (Parameter #27) when setting additional flow for multiple operation.
- Setting the following parameters will enhance the work tool operation along with other implement movement.
- Spool shift pressure adjustment to extend the attachment control valve.
"Atch #1 M-Ope Max Ext Press" (Parameter #32) - XXXX [kPa]
- Spool shift pressure adjustment to extend the attachment control valve.
Note: For reference, this parameter is set within the range of 800 kPa to 2000 kPa.
- Set the additional flow to the work tool when multiple operations are to take place by using the following parameter settings.
"Atch #1 Mult-Ope Add Flow Setting" (Parameter # 28) - XXX [L/min]
Note: Pump flow to the work tool may exceed the upper limit flow set (Parameter #27) when setting additional flow for multiple operation.
- Setting the following parameters will enhance the work tool operation along with other implement movement.
- Spool shift pressure adjustment to extend the attachment control valve.
"Atch #1 M-Ope Max Ext Press" (Parameter #32) - XXXX [kPa]
"Atch #2 M-Ope Max Ext Press" (Parameter #42) - XXXX [kPa]
Note: For reference, this parameter is set within the range of 800 kPa to 2000 kPa. A parameter setting for spool shift pressure of 0 kPa is not made for flow from two pumps.
- Spool shift pressure adjustment to extend the attachment control valve.
Enhanced Multiple Operation for Two Pump Flow
When operating the work tool with combined pump flow along with other functions (boom, stick, and swing), the control of the work tool can be improved using the following.
Note: This parameter setting is only available when "Multi Ope Atch Valve Limit" (Parameter # 14) is Enabled.
- The speed of the work tool when operating multiple functions at the same time can be increased or decreased. Increase the value of parameter to increase the speed. Decrease the value of the parameter to decrease the speed.
- Spool shift pressure adjustment to extend the attachment control valve when operating the work tool with Boom UP, Stick IN, and Swing.
"Single Mode Max Ext Press" (Parameter #15) - XXXX [kPa]
Set this parameter within the following range.
- "Single Mode Max Ext Press" (Parameter #15) greater than or equal to "Atch #1/#2 Max Ext Press" (Parameter #30 and #40)
- "Single Mode Max Ext Press" (Parameter #15) less than or equal to "Atch #1/#2 M-Ope Max Ext" (Parameter #32 and #42)
- Spool shift pressure adjustment to extend the attachment control valve when operating the work tool with Boom UP, Stick IN, and Swing.