Rear Power Take-Off (RPTO) - Install
Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 6V-4073 | Spanner Wrench | 1 |
| B | 138-7574 | Link Bracket | 1 |
| F | 1P-0520 | Driver Gp | 1 |
| G | 5P-6545 | Sleeve Installer | 1 |
- If the assembly of the Rear Power Take-Off Drive is not necessary then proceed to Step 10.
- Use Tooling (F) and a suitable press in order to press inner race (16) into the adapter drive.
Show/hide table
 | |
| Illustration 1 | g02286373 |
- Position retainer plate (15) and install bolts (14) .
- Position bearing (13) and spacer (12) onto drive gear (10). Use a suitable press, Tooling (F), and Tooling (G) in order to press the spacer and bearing into place.
Show/hide table
 | |
| Illustration 2 | g02286793 |
- Position drive gear (10) and drive adapter (11) into place on a suitable press. Position bearing (9) (not shown) into place on drive gear (10). Use Tooling (F), Tooling (G), and a suitable press in order to install bearing (9) onto drive gear (10) .
Show/hide table
 | |
| Illustration 3 | g02286834 |
- Install the lock and the locknut onto drive gear (10) .
- Attach Tooling (B) and a suitable lifting device to Rear Power Take-Off Drive (5). The weight of Rear Power Take-Off Drive (5) is approximately 32 kg (70 lb). Position Rear Power Take-Off Drive (5) and install bolts (8). Ensure that the locating dowel (X) is aligned.
Show/hide table
 | |
| Illustration 4 | g02282934 |
Show/hide table
 | |
| Illustration 5 | g02287136 |
- Use Tooling (A) in order to tighten locknut (6) to a torque of 406 ± 68 N·m (300 ± 50 lb ft). Bend the locking tabs on lock (7) into the slot of locknut (6) .
- Position cover (2) and install bolts (1) .
- Attach Tooling (B) and a suitable lifting device to the Rear Power Take-Off Drive. The weight of the Rear Power Take-Off Drive is approximately 32 kg (70 lb). Position the Rear Power Take-Off Drive and install bolts (4). Ensure that locating dowel (X) is aligned. Position cover (2) and install bolts (1) .
Show/hide table
 | |
| Illustration 6 | g02287414 |
Caterpillar Information System:
C175-16 Locomotive Engine Engine Oil Pressure - Test
C3.4B Engines Cylinder Is Noisy
C3.4B Engines Coolant Temperature Is High
2010/10/20 A New Camshaft Thrust Washer and Plate Are Used in C175-16 Generator Set Engines {1210, 1210, 7553}
C3.4B Engines Coolant Contains Oil
C3.4B Engines Battery Problem
C3.4B Engines Alternator Problem - Charging Problem and/or Noisy Operation
C6.6 Industrial Engine Flywheel Housing - Flywheel Housing that is Equipped with Rear Power Take-Off
C4.4 Industrial Engine Fuel Filter Base - Primary Fuel Filter Base
C1.5 and C2.2 Industrial Engines California Emission Control Warranty Statement
C1.5 and C2.2 Industrial Engines Federal Emission Control Warranty
C1.5 and C2.2 Industrial Engines Reference Material
320 VH and VM Variable Gauge Undercarriage Track Carrier Roller - Remove and Install - VM Undercarriage
G3500 A3 Engines Coolant Pressure Is High
G3500 A3 Engines Coolant Pressure Is Low
C9.3 Tier 4 Final Engines Electric Starting Motor
C3.4B Engines Electronic Service Tool Does Not Communicate
C3.4B Engines Engine Does Not Crank
C3.4B Engines Engine Has Mechanical Noise (Knock)
C3.4B Engines Engine Shutdown Occurs Intermittently
C6.6 Industrial Engine Exhaust Cooler (NRS) - Test
C9.3 Tier 4 Final Engines Pressure Sensor (NOx Reduction System)
C18 Generator Set Engines Secondary ECM Assumes Control
C9.3 Tier 4 Final Engines Temperature Sensor (NOx Reduction System)