Steering Control Valve - Remove and Install
拆卸步骤
Show/hide table
高温机油或高温部件可能会导致人身伤害。 在工作温度下,机油温度高,压力高。 热油能造成烫伤。 只能在发动机停机且加注口盖充分冷却到可以徒手触及时再卸下加注口盖。 不让高温油或部件与皮肤接触。 |
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 卸下机具和其油路之前,必须先把机具放到地面上,让油先冷却,才可进行工作。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
- 如果配备有抑噪配置,则请参阅专门说明书, " 351-3820 抑噪配置(如有配备)的安装",了解专用面板位置和正确的拆卸或安装步骤。
- 释放系统压力。 请参阅操作和保养手册, "系统压力释放"。
- 将液压油箱中的油排入合适的容器以便保存或废弃这些油。 请参阅操作和保养手册, "液压油箱油位 - 更换 - 转向系统",了解正确的排放和加注步骤。
- 断开软管组件 (1) 、软管组件 (2) 和软管组件 (3) 。 断开管组件 (4) 和软管组件 (5) 。
Show/hide table
图 1 | g02151689 |
- 断开软管组件 (6) 和软管组件 (7) 。 拆下卡箍 (8) 和卡箍 (9) 。
Show/hide table
图 2 | g02151706 |
- 断开管组件 (10) 。
Show/hide table
图 3 | g02151712 |
- 拆下螺栓 (11) 。 拆下转向控制阀 (12) 。
安装步骤
- 按与拆卸相反的顺序安装转向控制阀 (12) 。
Caterpillar Information System:
797F and 797F XQ Off-Highway Trucks Machine Systems Solenoid and Relief Valve (Steering) - Assemble
797F and 797F XQ Off-Highway Trucks Machine Systems Solenoid and Relief Valve (Steering) - Disassemble
797F and 797F XQ Off-Highway Trucks Machine Systems Solenoid and Relief Valve (Steering) - Remove and Install
C7.1 Industrial Engine Plate Locations and Film Locations - Engine Aftertreatment System
C9.3 Tier 4 Final Engines Valve Mechanism Cover
CEM Locomotive Aftertreatment Fluid Recommendations
349F and 352F Excavators Hydraulic System Check Valve (Return Makeup) - Slow Return Check Valve
C13 Industrial Engines Exhaust Diffuser Adapter
C18 Marine Engine Zinc Rods - Inspect/Replace
C9.3 Engines for Caterpillar Built Machines Exhaust Sensor Lines - Remove and Install
C13 Industrial Engines Exhaust Diffuser Adapter
C13, C15, and C18 Tier 4 Final Engines Exhaust Gas Valve (NRS)
797F and 797F XQ Off-Highway Trucks Machine Systems Steering Control Valve - Disassemble
797F and 797F XQ Off-Highway Trucks Machine Systems Steering Control Valve - Assemble
C9.3 Tier 4 Final Engines Fuel Filter Base - Primary
2010/05/24 A Redesigned Water Lines Group Is Now Used on Certain 3516B Locomotive Engines {1380}
C27 and C32 Engines for Caterpillar Built Machines ECM - Replace
C15 and C18 Engines for Caterpillar Built Machines Exhaust Manifold
C4.4 Industrial Engine Electrical System
C27 and C32 Tier 4 Engines Mounting Frame
C4.4 Industrial Engine Exhaust Cooler (NRS)
C13, C15, and C18 Tier 4 Final Engines Air Lines
325D and 329D Excavators Joystick Controls Alternate Patterns
C4.4 Industrial Engine Exhaust Gas Valve (NRS)