Lifter Group - Remove and Install - Hydraulic Lifter Group
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A(1) | 5P-7306 | Housing | 1 |
5P-7305 | Engine Turning Tool | 1 | |
B | 1U-7262 | Telescoping Magnet | 1 |
Show/hide table
(1) | This Tool is used in the aperture for the electric starting motor. |
Start By:
- Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install" for the correct procedure.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- If the crankshaft is installed, use Tooling (A) to rotate the crankshaft in order to gain access to the appropriate lifters .
- Use Tooling (B) in order to remove lifters (1).
Note: Place a temporary identification mark on each lifter in order to identify the correct location.
- Repeat Step 1 through Step 2 in order to remove the remaining lifters.
Show/hide table
Illustration 1 | g02008013 |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A(1) | 5P-7306 | Housing | 1 |
5P-7305 | Engine Turning Tool | 1 | |
B | 1U-7262 | Telescoping Magnet | 1 |
Show/hide table
(1) | This Tool is used in the aperture for the electric starting motor. |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Replace all lifters when a new camshaft is installed. |
- Clean the lifters. Follow Step 1.a through Step 1.c in order to inspect the lifters. Replace any worn lifters or damaged lifters.
- Inspect the seat of the pushrod in the lifter for visual wear and damage.
- Inspect the shank of the lifter for wear and damage. Refer to Specifications, "Lifter Group" for more information.
- Inspect the face of the lifter that runs on the camshaft for visual wear and damage.
- If the crankshaft is installed, use Tooling (A) to rotate the crankshaft in order to allow access for the installation of appropriate lifters (1).
Show/hide table
Illustration 2 g02008013 - Lubricate lifters (1) with clean engine oil.
- Use Tooling (B) to install lifters (1) to the cylinder block. Ensure that used lifters are installed in the correct location.
Note: The lifters should be free to rotate.
- Repeat Step 1 through Step 4 in order to install the remaining lifters.
End By:
- Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install" for the correct procedure.
Caterpillar Information System:
C4.4 Industrial Engine Speed/Timing Sensor
C6.6 Industrial Engine Cylinder Head - Install
C6.6 Industrial Engine Cylinder Head - Remove
C4.4 Industrial Engine Engine Oil Pressure Sensor
C6.6 Industrial Engine Rocker Shaft and Pushrod - Install
C6.6 Industrial Engine Rocker Shaft - Assemble
C18 Marine Engine Cooling System Coolant (ELC) - Change
C18 Marine Engine Cooling System Coolant (DEAC) - Change
C9.3 Engines for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
C18 Marine Engines Model View Illustrations
C18 Marine Engines Zinc Rods - Inspect/Replace
C18 Marine Engines Maintenance Recommendations
C4.4 Industrial Engine Inlet Manifold Temperature Sensor
C6.6 Industrial Engine Camshaft - Remove and Install
C6.6 Industrial Engine Camshaft Gear - Remove and Install
C4.4 Industrial Engine Boost Pressure Sensor
C4.4 Industrial Engine Water Pump
C6.6 Industrial Engine Camshaft Bearings - Remove and Install
C6.6 Industrial Engine Engine Oil Pan - Install - Aluminum Oil Pan
C6.6 Industrial Engine Engine Oil Pan - Remove - Aluminum Oil Pan
C6.6 Industrial Engine Engine Oil Pan Plate - Remove and Install - Aluminum Oil Pan
C4.4 Industrial Engine Balancer
C6.6 Industrial Engine Piston Cooling Jets - Remove and Install
12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Transmission Oil Lines