Camshaft Bearings - Remove and Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 8S-2241 | Camshaft Bearing Tool Group | 1 |
B | 8H-0684 | Ratchet Wrench | 1 |
Start By:
- Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove" for the correct procedure.
- Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install" for the correct procedure.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Inspect camshaft bearing (1). Refer to Specifications, "Camshaft Bearings" for more information.
- If camshaft bearing (1) is worn or damaged, use Tooling (A) in order to remove the camshaft bearing from the cylinder block.
Note: Remove the camshaft bearing from the front of the cylinder block.
Show/hide table
Illustration 1 | g02267614 |
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 8S-2241 | Camshaft Bearing Tool Group | 1 |
B | 8H-0684 | Ratchet Wrench | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Clean the bearing housing in the cylinder block. Ensure that the oil hole in the bearing housing is free from debris.
Show/hide table
Illustration 2 g02267633 - Lubricate the bearing housing in the cylinder block with clean engine oil.
- Accurately align large oil Hole (X) in camshaft bearing (1) with the oil hole in the cylinder block.
Note: The Groove (Y) in the camshaft bearing must be to the top of the cylinder block.
- Use Tooling (A) in order to install camshaft bearing (1) into the cylinder block. Install the camshaft bearing so that the front edge of the bearing is flush with the face of the recess in the cylinder block.
Note: Ensure that the oil holes are correctly aligned. If the oil is not correctly aligned, the camshaft bearing should be removed.
End By:
- Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install" for the correct procedure.
Caterpillar Information System:
C4.4 Industrial Engine Water Pump
C4.4 Industrial Engine Boost Pressure Sensor
C6.6 Industrial Engine Camshaft Gear - Remove and Install
C6.6 Industrial Engine Camshaft - Remove and Install
C4.4 Industrial Engine Inlet Manifold Temperature Sensor
C6.6 Industrial Engine Lifter Group - Remove and Install - Hydraulic Lifter Group
C4.4 Industrial Engine Speed/Timing Sensor
C6.6 Industrial Engine Cylinder Head - Install
C6.6 Industrial Engine Cylinder Head - Remove
C4.4 Industrial Engine Engine Oil Pressure Sensor
C6.6 Industrial Engine Rocker Shaft and Pushrod - Install
C6.6 Industrial Engine Rocker Shaft - Assemble
C6.6 Industrial Engine Engine Oil Pan - Install - Aluminum Oil Pan
C6.6 Industrial Engine Engine Oil Pan - Remove - Aluminum Oil Pan
C6.6 Industrial Engine Engine Oil Pan Plate - Remove and Install - Aluminum Oil Pan
C4.4 Industrial Engine Balancer
C6.6 Industrial Engine Piston Cooling Jets - Remove and Install
12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders Transmission Oil Lines
C6.6 Industrial Engine Pistons and Connecting Rods - Remove
C4.4 Industrial Engine Water Temperature Regulator and Housing
C6.6 Industrial Engine Pistons and Connecting Rods - Disassemble
C6.6 Industrial Engine Pistons and Connecting Rods - Assemble
C6.6 Industrial Engine Pistons and Connecting Rods - Install
C6.6 Industrial Engine Connecting Rod Bearings - Remove - Connecting Rods in Position