Ether Starting Aid - Test
系统运作描述:
在您测试乙醚喷射系统之前,先将乙醚罐从系统上拆下。
对乙醚系统进行故障诊断与排除或者激活或记录表 1 中的诊断代码时,采用此步骤。
Show/hide table
故障诊断代码     | |||
---|---|---|---|
CDL 代码     | J1939 代码     | 代码说明 (代码说明可能不同)     |
注释     |
2417-5     | 626-5     | 乙醚喷射控制电磁阀:电流低于正常值     | 系统将会锁定该代码。 将会记录该代码。 乙醚喷射已停用。     |
2417-6     | 626-6     | 乙醚喷射控制电磁阀:电流高于正常值     | 系统将会锁定该代码。 将会记录该代码。 乙醚喷射已停用。     |
乙醚喷射系统可改善发动机的寒冷天气起动性能。 电子控制模块(ECM)控制着乙醚喷射系统。 如果发动机停机为激活状态的话,乙醚喷射系统将被停用。
乙醚起动辅助根据冷却液温度、进气岐管温度和大气压力工况图动作。 请参阅插图 1。
Show/hide table
图 1 | g02445796 |
乙醚喷射系统启用时,必须符合以下条件:
- 将 Cat ET 中的乙醚喷射设为启用
- 发动机冷却液温度低于"起动辅助选择温度 -
冷却液"。 请参阅插图 1。
- 进气岐管温度低于"起动辅助选择温度 -
IMAT。"
- 冷却液温度和进气岐管空气温度在各自的 11° C 范围内。
Show/hide table
图 2 | g02462932 |
乙醚喷射系统示意图 |
Show/hide table
图 3 | g01696575 |
乙醚起动继电器装置总成(典型示例) (1) 乙醚喷射电磁阀 |
Show/hide table
图 4 | g02467497 |
P1 乙醚喷射系统的端子 (P1-11) 乙醚启用 (P1-18) 乙醚喷射回路 |
Show/hide table
图 5 | g01155187 |
乙醚电磁阀线束接头处的接线端位置 (1) 乙醚启用电磁阀 (2) 乙醚喷射回路电磁阀 |
Show/hide table
故障诊断与排除测试步骤     | 数值     | 结果     |
---|---|---|
1. 检查电气接头和配线 A. 断开 ECM 的电源。 B. 彻底检查 ECM 接头 J1/P1 和 J2/P2。 检查电路中的所有其他接头。 请参阅故障诊断与排除, "电气接头 - 检查"中的诊断功能测试。 C. 对 ECM 接头上与其电路有关的每一根导线进行拉力为 45 N (10 lb) 拉拔测试。 D. 检查 ECM 接头(六角头固定螺钉)的扭矩是否正确。 请参阅故障诊断与排除, "电气接头 - 检查"中的诊断功能测试。 E. 检查线束和配线有无磨损和挤压的地方。     |
连接松动或导线损坏     |
结果:线束和导线正常。 继续测试步骤 2。 结果:接头和/或配线有问题。 修理和/或更换接头或配线。 确保所有密封正确就位,接头联接。 继续测试步骤 4。     |
2. 检查 ECM 和乙醚控制装置间的配线 进行此步骤之前,必须拆下乙醚罐。 A. 确认钥匙开关处于 OFF 位置。 B. 拆卸乙醚罐。 C. D断开乙醚控制装置的发动机线束接头。 D. 在乙醚控制装置发动机线束接头的两个端子间连接数字电压表。 E. 把钥匙开关转到接通位置。 F. 在将钥匙开关转到 ON 的同时,测量端子间的电压。     |
10 VDC     | 结果:电压测量值为 0 VDC。 ECM 和乙醚控制装置线束接头间的电气部件有问题。 故障可能出在电气接头上。 进行必要的修理。 继续测试步骤 3。 结果:电压测量值大约 10 VDC。 ECM 和乙醚控制装置间的电气部件正常。 继续测试步骤 3。     |
3. 测量乙醚控制装置内线圈的电阻 A. 确认乙醚控制装置未与发动机线束相连。 B. 测量乙醚控制装置内线圈的电阻。     |
20 Ω     | 结果:电阻测量值约为 20 Ω。 继续测试步骤 4。 结果:电阻测量值并非约为 20 Ω。 更换乙醚控制装置。 继续测试步骤 4。     |
Show/hide table
图 6 | g02462341 |
回缩柱塞 |
Show/hide table
图 7 | g02462343 |
延伸柱塞 |
Show/hide table
故障诊断与排除测试步骤     | 数值     | 结果     |
---|---|---|
4. 核实修理 A. 启动乙醚喷射超越。 B. 确认超越启动时柱塞向上移动。     |
柱塞移动     |
结果:超越启动时柱塞向上移动。 安装乙醚罐后使机组恢复工作。     |
测试步骤 1.
按所列步骤顺序完成以上程序。
结果:
- 以上程序解决了此问题。 - 停止
- 以上程序没有解决问题。 -
修复: 联系您 Cat 代理商的技术通信员(TC)。 如需进一步的帮助,您的 TC 可以通过代理商解决方案网络(DSN)与您交谈。
停止
Caterpillar Information System:
Selecting Connectors and Preparing Cables for Wiring an Uninterruptible Power Supply{4480} Selecting Connectors and Preparing Cables for Wiring an Uninterruptible Power Supply{4480}
3516C Generator Sets Catalyst (DOC) - Replace
CEM Locomotive Aftertreatment Catalyst (DOC) - Clean/Inspect
793F Off-Highway Truck Machine Systems Solenoid Valve (Automatic Lubrication) - Remove and Install
C6.6 Generator Set Ignition Keyswitch Circuit and Battery Supply Circuit - Test
3508C, 3512C and 3516C Locomotive Engines Cylinder Head
C6.6 Generator Set Data Link Circuit - Test
Roller Servicing Equipment, Tooling, Literature, and Training Review {0374, 4154, 4180, 4181, 7561} Roller Servicing Equipment, Tooling, Literature, and Training Review {0374, 4154, 4180, 4181, 7561}
3508, 3512 and 3516 Generator Set Engines Tachometer Drive - Remove and Install
2010/02/19 A New Fuel Transfer Pump and a New Check Valve Are Now Used on Certain C32 Marine Engines {1256, 1262}
C6.6 Generator Set Fuel Rail Pump Solenoid - Test
C6.6 Generator Set CAN Data Link Circuit - Test
C27 and C32 Engines for Caterpillar Built Machines Cooling System - Test
C27 and C32 Engines for Caterpillar Built Machines Electronic Unit Injector - Adjust
793F Off-Highway Truck Machine Systems Hoist Electronic Control - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Engine Crankcase Pressure (Blowby) - Test
Bench Test Procedure For A CX35 On-Highway Transmission and a CX35-P800 Petroleum Transmission {3030, 3073} Bench Test Procedure For A CX35 On-Highway Transmission and a CX35-P800 Petroleum Transmission {3030, 3073}
3512E HD Petroleum Engine Product Description
C7 and C9 On-Highway Engines Diesel Particulate Filter Collects Excessive Soot
EMCP4.1/EMCP4.2 General Information
Updating the Wiring Harness of the Engine Brake on Some C15 Engines{1290, 1408, 1900} Updating the Wiring Harness of the Engine Brake on Some C15 Engines{1290, 1408, 1900}
C15 and C18 Petroleum Generator Sets Battery Disconnect Switch - If Equipped
G3500H 60Hz Generator Sets Fluid Recommendations
Idler Servicing Equipment, Tooling, Literature, and Training Review {0374, 0599, 4159, 4167, 7561} Idler Servicing Equipment, Tooling, Literature, and Training Review {0374, 0599, 4159, 4167, 7561}