Tachometer Drive - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1P-0510 | Driver Gp | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Disconnect the harness assembly from service meter (3). Remove bolts (4) and service meter (3).
- Disconnect the harness assembly from tachometer drive (1). Remove bolts (2) and tachometer drive (1).
- Remove the O-ring seal from tachometer drive (1).
Show/hide table
Illustration 2 g02056454 - Remove bolts (5), cover assembly (6), and the gasket. Remove the shaft from cover assembly (6).
Show/hide table
Illustration 3 g02056514 - Remove lip seal (8) from cover assembly (6). If necessary, remove bearing (7) and the dowels from cover assembly (6).
Show/hide table
Illustration 4 g02056515 - Remove bolt (10) and adapter (9).
Show/hide table
Illustration 1 | g02056453 |
- Install tachometer drive (1) in the reverse order of removal.
- Tighten bolt (10) to a torque of
360 ± 40 N·m (270 ± 30 lb ft) . Tap the adapter with a hammer. Tighten bolt (10) again to a torque of360 ± 40 N·m (270 ± 30 lb ft) . Repeat this procedure until the torque does not change. - Use Tooling (A) to install lip seal (8) and bearing (7), if necessary.
- Apply clean engine oil to the O-ring seal prior to installation.
- Tighten bolt (10) to a torque of
Caterpillar Information System:
2010/02/19 A New Fuel Transfer Pump and a New Check Valve Are Now Used on Certain C32 Marine Engines {1256, 1262}
C6.6 Generator Set Fuel Rail Pump Solenoid - Test
C6.6 Generator Set CAN Data Link Circuit - Test
C6.6 Generator Set CID 1779 FMI 08
2010/01/08 Correct Usage of Seals and Spacers on the Valve Mechanism Covers of Some C9 Engines {1107, 7555}
C6.6 Generator Set CID 1690 FMI 08
3512C HD Locomotive Engine Product Lifting
C6.6 Generator Set CID 2246 FMI 06
C6.6 Generator Set CID 1797 FMI 04
C6.6 Generator Set CID 1797 FMI 03
C6.6 Generator Set CID 1785 FMI 10
C6.6 Generator Set CID 1779 FMI 06
Roller Servicing Equipment, Tooling, Literature, and Training Review {0374, 4154, 4180, 4181, 7561} Roller Servicing Equipment, Tooling, Literature, and Training Review {0374, 4154, 4180, 4181, 7561}
C6.6 Generator Set Data Link Circuit - Test
3508C, 3512C and 3516C Locomotive Engines Cylinder Head
C6.6 Generator Set Ignition Keyswitch Circuit and Battery Supply Circuit - Test
793F Off-Highway Truck Machine Systems Solenoid Valve (Automatic Lubrication) - Remove and Install
CEM Locomotive Aftertreatment Catalyst (DOC) - Clean/Inspect
3516C Generator Sets Catalyst (DOC) - Replace
Selecting Connectors and Preparing Cables for Wiring an Uninterruptible Power Supply{4480} Selecting Connectors and Preparing Cables for Wiring an Uninterruptible Power Supply{4480}
C13, C15, and C18 Tier 4 Interim Engines Ether Starting Aid - Test
C27 and C32 Engines for Caterpillar Built Machines Cooling System - Test
C27 and C32 Engines for Caterpillar Built Machines Electronic Unit Injector - Adjust
793F Off-Highway Truck Machine Systems Hoist Electronic Control - Remove and Install