MID 027 - CID 3381 - FMI 04
产生此代码的情况:
Show/hide table
图 1 | g01991687 |
变速箱换档选择器开关的连接 |
该诊断代码与变速箱换档选择器开关有关。 当 ECU 确定电路的电压低于正常值时,记录 FMI 04。 此开关有两个到 ECU 的输入。 正常操作期间,其中一个输入为开路。 另一个输入接地。 使用电压表测量一个电路时,开路与接地之间会测得约 8 VDC,而闭路与接地之间会测得约 0 VDC。
产生此诊断代码的可能原因如下:
- "常开"信号电路(导线 961-BR(褐))与"常闭"信号电路(导线 962-OR(橙))同时对接地短路。
- 开关出现故障。
- ECU 有故障。 这不太可能。
执行该步骤前,检查电路中的线束接头。 不良连接经常是引起电路故障的原因。 确认电路中的所有连接都清洁紧固。 如果发现连接存在故障,则修复故障并在执行此步骤前核实该诊断代码为激活状态。下面的测试步骤可能会生成其他诊断代码。 忽略生成的这些诊断代码,并在修复原有诊断代码后清除这些忽略的诊断代码。 执行本步骤之前,请确保诊断代码 CID 3381 FMI 04 处于激活状态。
Show/hide table
开关的状态 | |||
---|---|---|---|
模式 | 开关位置 | J2-35
961-BR(褐) 电路 |
J2-40
962-OR(橙) 电路 |
主要 | 向上 | 开路 | 闭合 |
第二 | 向下 | 闭合 | 开路 |
测试步骤 1. 检查开关。
- 从机器线束上断开开关。
- 检查开关的触点 A 和触点 B 之间的导通性。
- 按下开关。 释放开关并检查是否导通。
- 检查开关的触点 B 和触点 C 之间的导通性。
- 按下开关。 释放开关并检查是否导通。
预期结果:
导通性检查的结果与表 1 中的规定一致。
结果:
- 正常 - 导通性检查的结果一致。 转至测试步骤 2。
- 异常 - 导通性检查的结果不一致。 开关出现故障。
修复: 更换开关。 确认使用新开关后诊断代码得到排除。
停止
测试步骤 2. 检查线束中的信号电路有无短路。
- 将开关重新连接到机器线束上。
- 从 ECU 上断开机器线束接头 J1 和 J2。
- 在 ECU 机器线束接头上,检查触点 J2-35(导线 961-BR(褐))与触点 J2-22(导线 993-BR(褐))之间的导通性。
- 按下开关。 释放开关并检查是否导通。
- 在 ECU 机器线束接头上,检查触点 J2-40(导线 962-BR(褐))与触点 J2-22(导线 993-BR(褐))之间的导通性。
- 按下开关。 释放开关并检查是否导通。
预期结果:
导通性检查的结果与表 1 中的规定一致。
结果:
- 正常 - 导通性检查的结果一致。
修复: 重新连接机器线束接头。 确认已排除诊断代码。 如果没有找到故障的起因,请咨询当地代理商征求 Caterpillar 可能的意见。 此咨询可以大大降低维修时间。 如果需要更换 ECU,请参阅测试和调整, KENR8291, "电子控制单元 - 更换"。
停止
- 异常 - 导通性检查的结果不一致。
修复: 机器线束中存在短路。 修理或更换机器线束。
停止
Caterpillar Information System:
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 3381 - FMI 03
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 3013 - FMI 04
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 3013 - FMI 03
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 2991 - FMI 12
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 2991 - FMI 09
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 2990 - FMI 12
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 2990 - FMI 09
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 1834 - FMI 02
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 1405 - FMI 06
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 1405 - FMI 05
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 1405 - FMI 03
C7.1 Industrial Engine Turbocharger - Inspect - High Pressure and Low Pressure Turbochargers
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System System Schematic
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System Transmission - Calibrate
C18 Industrial Engine Relay - Test
3508C, 3512C and 3516C Locomotive Engines Camshaft
3508C, 3512C and 3516C Locomotive Engines Air Inlet and Exhaust Lines
3406E, C-10 and C-12 Truck Engines Refill Capacities and Recommendations
793F Off-Highway Truck Engine Supplement Guard (Engine Oil Pan) - Remove and Install
2009/08/03 A New Support Assembly Is Now Available {0635, 4459}
Installing the New Air Compressor Groups on Some On-Highway Engines{1803} Installing the New Air Compressor Groups on Some On-Highway Engines{1803}
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 3395 - FMI 04
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 3396 - FMI 04
3406E, C-10, C-12, C-15, C-16 Truck Engines Refill Capacities and Recommendations