Engine, Torque Converter and Transmission - Connect
连接步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 9S-9082     | 发动机盘车工具     | 1     |
B     | 43-4614     | 举倾环 Columbus McKinnon Corporation     |
2     |
C     | 1U-9200     | 操纵杆滚轮举倾机构     | 1     |
D     | 350-4401     | 适配器板     | 1     |
E     | 1U-5750     | 发动机支座     | 1     |
1U-7508 | 适配器板     | 1     | |
1P-2850 | 排油车     | 1     | |
F     | 155-0695     | 螺纹锁固胶     | -     |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 检查 O 形密封圈、密封件和垫片。 更换磨损或损坏的 O 形密封圈、密封件和垫片。
注: 利用所密封的润滑剂润滑 O 形密封圈。
- 将工具 (B) 、工具 (C) 和适当的起吊设备连接至变矩器和变速箱 (2) 并连接到发动机上。 变矩器和变速箱 (2) 的重量约为 603 kg (1330 lb)。
Show/hide table
图 1 | g01959754 |
- 将变矩器和变速箱 (2) 从工具 (E) 上拆下。
Show/hide table
图 2 | g01959582 |
Show/hide table
图 3 | g01959584 |
- 拆下工具 (D) 。
Show/hide table
图 4 | g01959580 |
- 使用工具 (B) 、工具 (C) 和适当的起吊设备将变矩器和变速箱 (2) 定位到发动机上。 变矩器和变速箱 (2) 的重量约为 603 kg (1330 lb)。
Show/hide table
图 5 | g01959321 |
Show/hide table
图 6 | g01959753 |
- 安装螺栓 (3) 。 将螺栓 (3) 上紧到 80 ± 15 N·m (59 ± 11 lb ft) 的扭矩。
- 使用工具 (A) 转动飞轮。 将工具 (F) 涂抹到螺栓 (1) 上。 安装螺栓 (1) 。 将螺栓 (1) 拧紧至扭矩为 120 至 125 N·m (89 至 92 lb ft)。
注: 安装一个螺栓 (1) 。 转动飞轮大约 180°。 安装其余的螺栓 (1) 。
Show/hide table
图 7 | g01949288 |
End By: 安装电起动马达。 请参阅 拆解和组装, "电起动马达 - 拆卸和安装"。
Caterpillar Information System:
C13, C15, and C18 Tier 4 Interim Engines Crankcase Pressure Is Low
CX31-P600 Petroleum Transmission Well Servicing Engine, Torque Converter, and Transmission - Separate
C9.3 Industrial Engine Fuel Manifold - Remove and Install - Clean Emissions Module
2009/06/29 A Spring has been Added to the Ignition Transformer on G3400 and G3500 Engines {1550}
797F and 797F XQ Off-Highway Truck Power Train Final Drive
G3304B and G3306B Engines Engine Control Panel
3500 Engines Turbocharger - Install
G3304B and G3306B Engines Ignition Transformer - Test
2009/08/01 Changes to the Gasket for the Engine Oil Filter Base on Some C11 and C13 Engines {1306, 7555}
2009/08/03 Changes to the Gasket for the Engine Oil Filter Base on Some C11 and C13 Engines {1306, 7555}
Automatic Paralleling for the XQ2000 Power Module{7451} Automatic Paralleling for the XQ2000 Power Module{7451}
G3304B and G3306B Engines Gas Pressure - Check and Adjust
793F and 797F Off-Highway Trucks Braking System MID 116 - CID 0766 - FMI 02
C9.3 Engines for Caterpillar Built Machines Ignition Coil - Remove and Install - Clean Emissions Module
C9.3 Engines for Caterpillar Built Machines Relay (ARD Nozzle Heater) - Remove and Install - Clean Emissions Module
C9.3 Engines for Caterpillar Built Machines Air Control Valve - Remove and Install
C9.3 Engines for Caterpillar Built Machines Combustion Head - Remove and Install - Clean Emissions Module
G3300 Engines Manual Stop Procedure
G3512E Generator Set Engine Diagnostic Trouble Codes
3500 Engines Aftercooler - Remove and Install
2009/09/07 Updated Information on the Starter Motor Mag Switch (SMMS) for Electronic Controlled Marine Engines {1424, 1453, 7499}
G3512E Generator Set Engine Configuration Parameters
Quick Start Guide for Auto Paralleling{4450, 7451} Quick Start Guide for Auto Paralleling{4450, 7451}
C9.3 Engines for Caterpillar Built Machines Nozzle Heater Harness - Remove and Install - Harness Assembly