Engine, Torque Converter, and Transmission - Separate
分离步骤
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 9S-9082 | 发动机盘车工具 | 1 |
| B | 43-4614 | 举倾环 Columbus McKinnon Corporation |
2 |
| C | 1U-9200 | 操纵杆滚轮举倾机构 | 1 |
| D | 350-4401 | 适配器板 | 1 |
| E | 1U-5750 | 发动机支座 | 1 |
| 1U-7508 | 适配器板 | 1 | |
| 1P-2850 | 排油车 | 1 | |
开始:
- 拆下电起动马达。 有关指定的发动机，请参阅拆解和装配, "电起动马达 - 拆卸和安装"。
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
| 注意 |
|---|
在检验、保养、测试、调整及维修发动机时，请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前，要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品，请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 使用工具 (A) 转动飞轮。 拆下螺栓 (1 ) 。
Show/hide table
 | |
| 图 1 | g01949286 |
- 将工具 (B) 、工具 (C) 和适当的起吊设备连接至变矩器和变速箱 (2) 。 变矩器和变速箱 (2) 的重量约为 603 kg (1330 lb)。 请参阅专门说明书, REHS3513, "起吊"和操作和保养手册, SEBU8427, "起吊和系紧变速箱"。
Show/hide table
 | |
| 图 2 | g01959321 |
Show/hide table
 | |
| 图 3 | g01959753 |
- 拆下螺栓 (3 ) 。
- 拆下变矩器和变速箱 (2) 。
- 安装工具 (D) 。
Show/hide table
 | |
| 图 4 | g01959323 |
- 将变速箱和变矩器 (2) 安装到工具 (E) 上。
注: 需要使用三个 1/2-20 螺栓和一个 3/8-24 螺栓将变速箱安装到工具 (E) 上。
Show/hide table
 | |
| 图 5 | g01839514 |
Show/hide table
 | |
| 图 6 | g01959344 |
Caterpillar Information System:
C9.3 Industrial Engine Fuel Manifold - Remove and Install - Clean Emissions Module
2009/06/29 A Spring has been Added to the Ignition Transformer on G3400 and G3500 Engines {1550}
797F and 797F XQ Off-Highway Truck Power Train Final Drive
G3304B and G3306B Engines Engine Control Panel
3500 Engines Turbocharger - Install
G3304B and G3306B Engines Ignition Transformer - Test
2009/08/01 Changes to the Gasket for the Engine Oil Filter Base on Some C11 and C13 Engines {1306, 7555}
2009/08/03 Changes to the Gasket for the Engine Oil Filter Base on Some C11 and C13 Engines {1306, 7555}
Automatic Paralleling for the XQ2000 Power Module{7451} Automatic Paralleling for the XQ2000 Power Module{7451}
G3304B and G3306B Engines Gas Pressure - Check and Adjust
2009/08/10 A New Connecting Rod Assembly Is Being Used In The G3600 Engines With A Compression Ratio of 9.2:1 {1218}
G3304B and G3306B Engines Cylinder Liner Projection - Inspect
C13, C15, and C18 Tier 4 Interim Engines Crankcase Pressure Is Low
CX31-P600 Petroleum Transmission Well Servicing Engine, Torque Converter and Transmission - Connect
793F and 797F Off-Highway Trucks Braking System MID 116 - CID 0766 - FMI 02
C9.3 Engines for Caterpillar Built Machines Ignition Coil - Remove and Install - Clean Emissions Module
C9.3 Engines for Caterpillar Built Machines Relay (ARD Nozzle Heater) - Remove and Install - Clean Emissions Module
C9.3 Engines for Caterpillar Built Machines Air Control Valve - Remove and Install
C9.3 Engines for Caterpillar Built Machines Combustion Head - Remove and Install - Clean Emissions Module
G3300 Engines Manual Stop Procedure
G3512E Generator Set Engine Diagnostic Trouble Codes
3500 Engines Aftercooler - Remove and Install
2009/09/07 Updated Information on the Starter Motor Mag Switch (SMMS) for Electronic Controlled Marine Engines {1424, 1453, 7499}
G3512E Generator Set Engine Configuration Parameters