Crankcase Pressure Is Low
本程序涉及以下故障诊断代码:
注: 以下代码可能不适用于特定的应用。
Show/hide table
故障诊断代码     | |||
---|---|---|---|
CDL 代码     | J1939 代码     | 说明 (代码说明可能不同)     |
注释     |
E994(2)     |     | 曲轴箱压力低     | 当曲轴箱压力已低于最小值编程设定的时间长度时,发动机控制模块(ECM)激活此代码。 黄色报警指示灯会点亮。 记录该代码。 发动机功率减额。     |
Show/hide table
图 1 | g02211761 |
典型的曲轴箱通风系统 (1) 曲轴箱压力传感器 (2) 呼吸器 (3) 滤清器壳体 (4) 烟气排放管 |
Show/hide table
图 2 | g02013955 |
发动机左侧 (5) 单向阀 |
可能原因
- 机油加注口盖关闭。
- 油位表(油尺)未完全座合。
- 未安装曲轴箱通气滤清器。
- 呼吸器和呼吸器滤罐之间的管未连接。
发动机配有开式曲轴箱通风系统。
建议的措施
Show/hide table
故障诊断与排除测试步骤     | 数值     | 结果     |
---|---|---|
1. 发动机通风 A. 建立 Caterpillar 电子技师(ET)和 ECM 之间的通信。 如有必要,请参阅故障诊断与排除, "电子维修工具"。 B. 在执行任何故障诊断与排除或清除故障诊断代码前,从发动机 ECM 下载"保修报告"。 C. 检查发动机。 查看有无以上列出的情况。     |
通风     |
结果:找到了可能的原因。 进行必要的修理。 复位所有激活的代码并清除所有记录的代码。 利用 Cat ET 确认故障已排除。     |
按所列步骤顺序完成以上步骤。
如果以上步骤未解决问题,请联系当地 Cat 代理商的技术通信员(TC)。 如需进一步的帮助,您的 TC 可以通过代理商解决方案网络(DSN)与您交谈。
Caterpillar Information System:
CX31-P600 Petroleum Transmission Well Servicing Engine, Torque Converter, and Transmission - Separate
C9.3 Industrial Engine Fuel Manifold - Remove and Install - Clean Emissions Module
2009/06/29 A Spring has been Added to the Ignition Transformer on G3400 and G3500 Engines {1550}
797F and 797F XQ Off-Highway Truck Power Train Final Drive
G3304B and G3306B Engines Engine Control Panel
3500 Engines Turbocharger - Install
G3304B and G3306B Engines Ignition Transformer - Test
2009/08/01 Changes to the Gasket for the Engine Oil Filter Base on Some C11 and C13 Engines {1306, 7555}
2009/08/03 Changes to the Gasket for the Engine Oil Filter Base on Some C11 and C13 Engines {1306, 7555}
Automatic Paralleling for the XQ2000 Power Module{7451} Automatic Paralleling for the XQ2000 Power Module{7451}
G3304B and G3306B Engines Gas Pressure - Check and Adjust
2009/08/10 A New Connecting Rod Assembly Is Being Used In The G3600 Engines With A Compression Ratio of 9.2:1 {1218}
CX31-P600 Petroleum Transmission Well Servicing Engine, Torque Converter and Transmission - Connect
793F and 797F Off-Highway Trucks Braking System MID 116 - CID 0766 - FMI 02
C9.3 Engines for Caterpillar Built Machines Ignition Coil - Remove and Install - Clean Emissions Module
C9.3 Engines for Caterpillar Built Machines Relay (ARD Nozzle Heater) - Remove and Install - Clean Emissions Module
C9.3 Engines for Caterpillar Built Machines Air Control Valve - Remove and Install
C9.3 Engines for Caterpillar Built Machines Combustion Head - Remove and Install - Clean Emissions Module
G3300 Engines Manual Stop Procedure
G3512E Generator Set Engine Diagnostic Trouble Codes
3500 Engines Aftercooler - Remove and Install
2009/09/07 Updated Information on the Starter Motor Mag Switch (SMMS) for Electronic Controlled Marine Engines {1424, 1453, 7499}
G3512E Generator Set Engine Configuration Parameters
Quick Start Guide for Auto Paralleling{4450, 7451} Quick Start Guide for Auto Paralleling{4450, 7451}