Engine Speed/Timing Sensors - Check/Clean/Calibrate
Show/hide table
Illustration 1 | g01068233 |
(1) Harness assembly
(2) Sensor (3) Bolt |
- Disconnect the harness assembly.
- Remove the bolt and the sensor.
- Remove the O-ring seal from the sensor.
Procedure for Cleaning, Inspecting, and Calibration
Check the condition of the plastic end of the sensor for wear and for contaminants. Clean the metal shavings and other debris from the face of the sensor. Use the procedure in the Troubleshooting Guide in order to calibrate the sensor.
- Install a new O-ring seal on the sensor. Lubricate the O-ring seal with clean engine oil.
- Position the sensor in the housing and install the bolt.
- Connect the harness assembly.
Crankshaft Speed/Timing Sensor
Show/hide table
Illustration 2 | g01895213 |
(4) Sensor
(5) Harness Assembly (6) Bolt |
- Disconnect the harness assembly.
- Remove the bolt and the sensor.
- Remove the O-ring seal from the sensor.
Procedure for Cleaning, Inspecting, and Calibration
Check the condition of the plastic end of the sensor for wear and for contaminants. Clean the metal shavings and other debris from the face of the sensor. Use the procedure in the Troubleshooting Guide in order to calibrate the sensor.
- Install a new O-ring seal on the sensor. Lubricate the O-ring seal with clean engine oil.
- Install the position sensor in the front housing and install the bolt.
- Connect the harness assembly.
Caterpillar Information System:
C13 Engines for Caterpillar Built Machines Ignition Coil - Remove and Install - Clean Emissions Module
C-15 and C-16 Industrial Engines Engine Speed/Timing Sensors - Check/Clean/Calibrate
C9.3 Engines for Caterpillar Built Machines Injector Trim File - Install
C13 Tier 4 Final Engines General Information - C13 Engines
2009/04/27 How Is Service Information Accessed / Used {1000}
793F and 797F Off-Highway Trucks Braking System MID 116 - CID 1437 - FMI 05
C9.3 Engines for Caterpillar Built Machines ECM Software - Install
C27 and C32 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install - C32
3412C Generator Set Generator Bearing Temperature - Measure/Record
C9.3 Engines for Caterpillar Built Machines Electrical Connectors - Inspect
C11 and C13 Industrial Engines Turbocharger
C13, C15, and C18 Tier 4 Final Engines Turbocharger
Improved Outlet Pipe for the Turbocharger{1052, 1353} Improved Outlet Pipe for the Turbocharger{1052, 1353}
793F CMD (Conversion) Off-Highway Truck Braking System MID 116 - CID 0835 - FMI 08
C15 and C18 Industrial Engines Air Inlet Elbow - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Assemble
793F and 797F Off-Highway Trucks Braking System MID 116 - CID 1607 - FMI 03
793F and 797F Off-Highway Trucks Braking System MID 116 - CID 1607 - FMI 05
793F and 797F Off-Highway Trucks Braking System MID 116 - CID 1607 - FMI 06
C13 Tier 4 Final Engines Electronic Control System Components
793F and 797F Off-Highway Trucks Braking System MID 116 - CID 1608 - FMI 03
793F and 797F Off-Highway Trucks Braking System MID 116 - CID 1608 - FMI 05
C1.5 and C2.2 Industrial Engines Cold Weather Starting
C7.1 Industrial Engine and Generator Set CAN Data Link Circuit - Test