C7.1 Industrial Engine and Generator Set Caterpillar


Sensors and Electrical Connectors

Usage:

C7.1 770
The Electronic Control Module (ECM) and most of the engine sensors are located on the left side of the engine. Refer to Illustration 1. For the remaining sensors that are attached to the engine, refer to Illustration 3. For the sensors and components on the Clean Emissions Module (CEM), refer to Illustration 5.

Note: In the following illustrations, some components have been removed in order to improve visibility.



Illustration 1g02311267
Sensor locations on the left side of the C7.1 engine
(1) Coolant temperature sensor
(2) Fuel temperature sensor
(3) Solenoid for the high-pressure fuel pump
(4) Intake manifold air temperature sensor
(5) Intake manifold pressure sensor
(6) Fuel rail pressure sensor
(7) 31-pin connector for the CEM
(8) Electronic Control Module (ECM)
(9) Barometric pressure sensor
(10) Primary speed/timing sensor
(11) Oil pressure sensor


Illustration 2g02311353
Close up views of sensor locations on the left side of C7.1 engine
(1) Coolant temperature sensor
(2) Fuel temperature sensor
(3) Solenoid for the high-pressure fuel pump
(4) Intake manifold air temperature sensor
(5) Intake manifold pressure sensor
(6) Fuel rail pressure sensor
(7) 31-pin connector for the CEM
(8) Electronic Control Module (ECM)
(9) Barometric pressure sensor
(10) Primary speed/timing sensor
(11) Oil pressure sensor


Illustration 3g02313313
Sensor locations on the right side and top of the C7.1 engine
(12) NOx Reduction System (NRS) differential pressure sensor
(13) NRS inlet pressure sensor
(14) NRS inlet temperature sensor
(15) NRS valve including a position sensor
(16) Engine intake throttle valve including a position sensor
(17) Wastegate regulator
(18) Secondary speed/timing sensor


Illustration 4g02313374
Close up views of sensor locations on the top of C7.1 engine
(12) NOx Reduction System (NRS) differential pressure sensor
(13) NRS inlet pressure sensor
(14) NRS inlet temperature sensor
(15) NRS valve including a position sensor
(16) Engine intake throttle valve including a position sensor
(17) Wastegate regulator


Illustration 5g02854896
Sensors and components on a typical CEM
(19) Soot antenna
(20) Aftertreatment Regeneration Device (ARD) ignition coil
(21) ARD air pressure sensor
(22) Heater relay for the ARD nozzle
(23) Inlet pressure sensor for the DPF
(24) Inlet temperature sensor for the DPF
(25) Soot antenna
(26) 40-pin harness connector
(27) ARD pilot fuel control valve
(28) ARD pilot fuel pressure sensor
(29) Aftertreatment ID module
(30) ARD combustion air valve including a position sensor
(31) Spark plug

Caterpillar Information System:

C4.4 Industrial Engine Piston and Rings
C6.6 Industrial Engine Main Bearing Journal
C6.6 Industrial Engine Cylinder Head Valves
C13 Engines for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install - C15 Engine
C13 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
C13 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C13 Engine for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
793F and 797F Off-Highway Trucks Braking System Brakes Drag
C12 Marine Engines Heat Exchanger - Inspect/Clean
793F CMD Off-Highway Truck (Command for Hauling) Power Train Electronic Control System Backup Alarm Does Not Function
C15 and C18 Engines for Caterpillar Built Machines Cylinder Head - Remove and Install
MP-15, MP-20, MP-30 and MP-40 Multi Processors Hydraulic Rotator
C13, C15, and C18 Tier 4 Interim Engines Oil Contains Coolant
C15 and C18 Industrial Engines Atmospheric Pressure Sensor - Remove and Install
C12 Marine Engines Engine Valve Lash - Inspect/Adjust
C15 and C18 Engines for Caterpillar Built Machines Crankcase Pressure Sensor - Remove and Install
C12 Marine Engines Fuel System Secondary Filter - Replace
C13, C15, and C18 Tier 4 Interim Engines Engine Does Not Crank
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pressure Sensor - Remove and Install
C13, C15, and C18 Tier 4 Interim Engines Engine Has Early Wear
C9.3 Engines for Caterpillar Built Machines Fuel Consumption Is Excessive
C13 Engine for Caterpillar Built Machines Crankshaft Rear Seal - Remove and Install
C32 Auxiliary Engine Maintenance Recommendations
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.