Cylinder Head Valves
Show/hide table
Illustration 1 | g01927355 |
Typical example (1) Exhaust valve spring (2) Inlet valve spring |
When the valve springs are replaced the valve springs must be replaced in pairs.
Refer to table 1 and table 2 for information on the length of the valve spring and the load of the valve spring.
Show/hide table
The load for the inlet valve spring | The length of the inlet valve spring |
|
|
|
|
Note: The free length for the inlet valve spring is
Show/hide table
The load for the exhaust valve spring | The length of the exhaust valve spring |
|
|
|
|
Note: The free length for the exhaust valve spring is
Show/hide table
Illustration 2 | g01927357 |
Typical example |
(3) Valve face angle
- Inlet ... 30 degrees
- Exhaust ... 45 degrees
(4) Valve stem diameter
- Inlet ...
6.970 to 6.985 mm (0.2744 to 0.2750 inch) - Exhaust ...
6.945 to 6.960 mm (0.2734 to 0.2740 inch) - Exhaust ...
Clearance
- Maximum clearance of the inlet valve stem ...
0.05 mm (0.0020 inch) - The service limit for the inlet valve stem ...
0.08 mm (0.0031 inch) - The service limit for the inlet valve stem ...
Clearance
- Maximum clearance of the exhaust valve stem ...
0.075 mm (0.00295 inch) - The service limit for the exhaust valve stem ...
0.10 mm (0.00394 inch) - The service limit for the exhaust valve stem ...
(5) Length of valve
- Inlet valve ...
109.82 to 110.27 mm (4.32361 to 4.34133 inch) - Exhaust valve ...
109.853 to 110.303 mm (4.32491 to 4.34263 inch) - Exhaust valve ...
(6) Valve head
- Diameter of inlet valve head ...
35 mm (1.37795 inch) - Diameter of exhaust valve head ...
33 mm (1.2992 inch) - Diameter of exhaust valve head ...
Caterpillar Information System:
C13 Engines for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install - C15 Engine
C13 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
C13 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C13 Engine for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
793F and 797F Off-Highway Trucks Braking System Brakes Drag
C12 Marine Engines Heat Exchanger - Inspect/Clean
793F CMD Off-Highway Truck (Command for Hauling) Power Train Electronic Control System Backup Alarm Does Not Function
C15 and C18 Engines for Caterpillar Built Machines Cylinder Head - Remove and Install
C9.3 Tier 4 Interim Engines Engine Cranks but Does Not Start
C6.6 Industrial Engine Lifter Group
C13 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C6.6 Industrial Engine Main Bearing Journal
C4.4 Industrial Engine Piston and Rings
C7.1 Industrial Engine and Generator Set Sensors and Electrical Connectors
MP-15, MP-20, MP-30 and MP-40 Multi Processors Hydraulic Rotator
C13, C15, and C18 Tier 4 Interim Engines Oil Contains Coolant
C15 and C18 Industrial Engines Atmospheric Pressure Sensor - Remove and Install
C12 Marine Engines Engine Valve Lash - Inspect/Adjust
C15 and C18 Engines for Caterpillar Built Machines Crankcase Pressure Sensor - Remove and Install
C12 Marine Engines Fuel System Secondary Filter - Replace
C13, C15, and C18 Tier 4 Interim Engines Engine Does Not Crank
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pressure Sensor - Remove and Install
C13, C15, and C18 Tier 4 Interim Engines Engine Has Early Wear