Idler Gear - Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 230-6284 | 定时销(凸轮轴) | 1 |
B | 230-6283 | 定时销(曲轴) | 1 |
C | 9U-7324 | 千分表支架 | 1 |
7H-1942 | 千分表 | 1 | |
3S-3268 | 千分表触针 | 1 | |
7H-1940 | 通用附件 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保 1 号活塞在压缩冲程的上死点位置。 请参阅系统操作、测试和调整 , "确定 1 号活塞上止点位置 "。
Show/hide table
图 1 g01473492 定时标记的对齐 - 确保已将工具 (A) 安装在凸轮轴齿轮 ( 1) 的孔 (X) 中。
- 确保已将工具 (B) 安装在缸体的孔 ( Y)中。 使用工具 (B),将曲轴锁定到位。
Show/hide table
图 2 g01473904 典型实例 - 清洁惰轮 (2) 的组件,然后检查惰轮组件是否磨损或损坏。 有关更多资料,请参阅 技术规格, "齿轮总成(前) "。 如有必要,更换惰轮组件。
- 使用清洁的发动机机油润滑惰轮组件 ( 2) 中的轴承。
Show/hide table
图 3 g01473909 典型实例 - 使惰轮 (2) 上的定时标记与凸轮轴齿轮上的定时标记对齐。 请参阅插图 1。 将惰轮 (2) 组件安装到定时箱的凹槽中。 确保识别标记上部 朝上。
注: 在安装过程中惰轮必须保持倾斜。 确保将惰轮组件中的孔与缸体中的孔对齐。
- 安装螺栓 (3)。 将螺栓拧紧至扭矩
44 N·m (32 lb ft) 。Show/hide table图 4 g01269937 使用千分表总成检查端隙 - 使用工具 (C) 检查惰轮 ( 2) 的端隙。 有关更多资料,请参阅 技术规格, "齿轮总成(前) "。
- 使用工具 (C) 检查惰轮与凸轮轴齿轮之间的齿隙。 有关更多资料,请参阅 技术规格, "齿轮总成(前) "。
- 使用工具 (C) 检查惰轮与曲轴齿轮之间的齿隙。 有关更多资料,请参阅 技术规格, "齿轮总成(前) "。
- 使用清洁的发动机机油稍微润滑所有的齿轮。
结束:
- 安装喷油泵齿轮。 请参阅拆解和组装燃油泵齿轮 -, "安装" 。
- 如果发动机配备空气压缩机,则安装该空气压缩机。 请参阅拆解和组装 , "空气压缩机 - 拆卸和安装" 。
- 如果发动机配备真空泵,则安装该真空泵。 请参阅拆解和组装真空泵 - 拆卸和, "安装" 。
- 如果发动机配备附件驱动,则安装该附件驱动。 请参阅拆解和组装附件驱动 - 拆卸和, "安装"。
Caterpillar Information System:
C4.4 Industrial Engine Idler Gear - Install
C4.4 Industrial Engine Idler Gear - Remove
C4.4 Industrial Engine Idler Gear - Remove
Monitoring Parameters Are Not Activated Until the Engine's RPM Has Reached Low Idle{1000, 1901, 1920} Monitoring Parameters Are Not Activated Until the Engine's RPM Has Reached Low Idle{1000, 1901, 1920}
Surface Finishes of Cylinder Bores{7562} Surface Finishes of Cylinder Bores{7562}
C12 Marine Engines Cooling System Supplemental Coolant Additive (SCA) - Test/Add
789D, 793F, and 797F Off-Highway Truck Monitoring System MID 053 - CID 0168 - FMI 03
C175-16 and C175-20 Generator Set Engines Turbocharger Speed Change Occurrence
C175-16 and C175-20 Generator Set Engines Fuel Pressure Is High - Fuel Supply System
Procedure to Replace the Top Glass on the Cab of Certain Excavators and Mobile Hydraulic Power Units{7301, 7310, 7325} Procedure to Replace the Top Glass on the Cab of Certain Excavators and Mobile Hydraulic Power Units{7301, 7310, 7325}
795F AC and 795F AC XQ Off-Highway Trucks Inverter Cabinet - Check/Clean
UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies System Shutdown
UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Reference Material
345D, 349D and 349D2 Excavator Machine System Specifications Air Cleaner - Precleaner
Motor Grader Circle Pinion Reuse {5207} Motor Grader Circle Pinion Reuse {5207}
C18 Industrial Engine Fuel Filter Differential Pressure - Test
2009/03/09 New Recommendations for C7 through C32 Marine Engines that Are Cooled by a Heat Exchanger {1379, 1395}
2009/05/18 A New Fan Spider Assembly Is Used {1356, 1360}
CX31-P600 Petroleum Transmission Well Servicing Transmission and Torque Converter - Separate
CX31-P600 Petroleum Transmission Well Servicing Transmission and Torque Converter - Connect
XQ175 Rental Generator Set Generator Lead Connections
CX31-P600 Petroleum Transmission Specifications
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks ECM - Replace
2009/03/09 Hard Starting of 3456 and C15 Generator Sets {1261, 1263}