5P4149 Conversion Group To Become A Discontinued Item On October 1, 1978{0650,1254}
Usage:
The 5P4149 Conversion Group and Special Instruction Form SMHS6700 are available for the conversion of the 8S2242 Nozzle Tester Group into the 5P4150 Tester Group. Installation of the conversion group permits a dealer to use the older tester to check the valves in both pencil-type and capsule-type fuel injection nozzles. The new 5P4150 Nozzle Tester Group already has the ability to check both types of valves.
After October 1, 1978, the 5P4149 Conversion Group will no longer be available for parts service. If you have the older 8S2242 Nozzle Tester Group and need the 5P4149 Conversion Group, order it now to make the conversion.
Caterpillar Information System:
1978/03/27 How To Find Correct Oil Change Intervals For Truck Engines Operated In Short Distance Applications (Pick Up And Delivery Service){1318,7500,0374}
1978/03/27 9N3700 Or 9N3299 Nozzle Assemblies Must Be Used On 3208 Engines That Are Equipped With Exhaust Gas Recirculation (EGR){1254}
1978/03/27 Improved Thrust Washers Now Used With Planet Gears{3000,3072,3106,3110,3003,3001,3100,3116,3159,3176,3107,5150,5165}
1978/03/27 5P8675 Extension Handle Available For General Uses{0614}
1978/03/27 Use 5P8706 Die Repair Kit For The Repair Of 9S6331 Die Assembly{0623}
1978/03/20 "Danger Do Not Operate" Tags Now Available{0374}
1978/03/13 The Causes And Reduction Of White Exhaust Smoke During Cold Engine Starts; Maintenance Aids Available To Decrease This Problem{1250,1383,1050}
1978/03/13 Soft Washers And Lockwashers Are Now Used With The Mounting Bolts For Air-Fuel Ratio Control{1278,1264}
1978/03/13 When A 6N5906 Hour Meter Will Not Operate Correctly, Check The Electrical Supply Before A Replacement Hour Meter Is Installed{7480,1400}
1978/03/13 5P8687 Tee Test Tooling Group{0651,5050}
1978/03/06 New Starter Motors Have Solenoid On Top Of Starter{1407,1453}
1978/03/06 Use Again Specifications For Valve Springs Are Changed{1108}
1978/03/27 More Torque Now Used To Tighten The Retainer Nut For Turbocharger Compressor{1052,1053}
1978/03/27 Correct Adjustment Of The Governor Control Linkage In Truck Engines Is Necessary To Prevent Low Power{1265,1269}
1978/04/03 Procedure For Alignment Of Transmission Mounting Parts On 1100 Series And 3208 Truck Engines With Allison MT640, MT650, And AT540 Series Transmissions{3000,1156,1157}
1978/04/03 A Gasket Group Is Available To Give Improved Sealing For The Oil Supply To The Rocker Arms On Early Engines{1101,1102,1221}
1978/04/10 New Piston Group With Better Service And Operation Characteristics Now Available{1214}
1978/04/10 New 5P9693 Reusable Cable Tie For Storage Of Wires, Cables And Tubing{0630}
1978/04/10 New Lifting Eye Group Used On 3412 Industrial Engines Equipped With Turbochargers{1101,1000}
1978/04/17 Improved Yokes, Hardened Washers And More Torque Keep Valve Lifter Guides Tight {1209}
1978/04/17 Locating Bushings For The 5P3550 Rod Boring Machine Will Now Hold Tapered Piston Pin Bushings {0626}
1978/04/17 Improved Oil Suction Tube Assembly {3300,3302}
1978/04/24 Use 6V100 Tool Arrangement To Remove And Install Piston Pin Bearings For Both Tapered And Standard Connecting Rods{0620,1218}
1978/04/24 Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}