Magnetic Screen (Transmission)
Show/hide table
| |
| Illustration 1 | g06299482 |
|
Magnetic screen (1) Tube assembly (2) Screen (3) Cover and bolts for the suction screen | |
Show/hide table
| |
| Illustration 2 | g06299513 |
|
Construction of the magnetic screen (1) Tube assembly (2) Screen (3) Cover (4) Magnets (5) Outlet to pump inlet (6) O-ring seal (7) Locknut (8) Inlet | |
The magnetic screen is fastened to the inlet port of the gear pump. Oil from the bottom of the transmission case flows through screen (2). Screen (2) filters the large foreign material as the oil flows through the screen. Then, the oil flows through tube assembly (3). The oil flows through the openings that are between magnets (4). The magnets are installed on the tube assembly so that the same magnetic ends are next to each other.
As the oil flows over the magnets, metal particles are stopped by the magnets. The oil then flows to outlet (5) and on to the gear pump. Then, oil is sent to the two transmission oil filters and continues to the transmission and torque converter hydraulic systems.
Caterpillar Information System:
D3-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Fuel System Filter (In-Line) - Replace
D-Series and D2-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Equipment Lowering Control Valve - Check
C175-16 Locomotive Engine Accessory Drive
Front Drive Shaft Bearing Lip Seals May Fail on Certain Wheel Dozers and Large wheel Loaders {3159, 3253} Front Drive Shaft Bearing Lip Seals May Fail on Certain Wheel Dozers and Large wheel Loaders {3159, 3253}
C175-16 Locomotive Engine Flywheel
D3-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Axle Bearings - Lubricate - MTL Only
Magnetic Pick Up (MPU1) Sensor Calibration Procedure for Certain Cat® Products {1912} Magnetic Pick Up (MPU1) Sensor Calibration Procedure for Certain Cat® Products {1912}
D3-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Capacities (Refill)
D3-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Radiator Tilting
330 and 330 GC Excavator Machine System Pump Control (Output Flow) - Adjust
330 and 330 GC Excavator Machine System Pump Control (Output Flow) - Test - One Pump Calibration (Optional Test)
330 and 330 GC Excavator Machine System Main Pump (Flow) - Test - Hydraulic Power
D3-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Fuel System Primary Filter (Water Separator) - Drain
Installing GRADE Firmware on the EC520 Controller through the Web Interface or Winflash {7620} Installing GRADE Firmware on the EC520 Controller through the Web Interface or Winflash {7620}
D9R Track-Type Tractor Power Train Transmission Hydraulic Control Valve - Remove and Install
CX48–P2560–3060 Petroleum Transmission Transmission Planetary
D8T Track-Type Tractor Engine Supplement Temperature Sensor (DPF Inlet, Flame Detect) - Remove and Install
C175-16 Locomotive Engine Solenoid Valve - Test - Engine
D3-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Fuel System Primary Filter (Water Separator) Element - Replace
C175-16 Locomotive Engine Diagnostic Trouble Codes
D3-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Fuel System Priming Pump - Operate
D3-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Fuses - Replace
C175-16 Locomotive Engine Event Codes
C175-16 Locomotive Engine DEF Pressure Is High