Gear Pump (Torque Converter and Transmission) - Remove
拆卸步骤
注: 为便于安装，在所有软管组件、所有管组件上做出识别标记。 插接好所有软管组件和所有管组件。 这将有助于防止液体渗漏，并有助于防止污物进入系统。
- 拆下螺栓 (2) 和法兰。 拆下管组件 (1) 。 拆下软管组件 (3) 和 (4) 。
Show/hide table
 | |
| 图 1 | g01440184 |
- 松开软管卡箍 (6) ，然后拆下软管 (7) 。 拆下螺栓 (6) 和法兰。
Show/hide table
 | |
| 图 2 | g01440188 |
- 拆下螺栓 (11) 。 需要两个人来拆卸齿轮泵 (8) 。 齿轮泵 (8) 的重量约为 27 kg (60 lb)。
Show/hide table
 | |
| 图 3 | g01440195 |
- 拆下螺栓 (9) ，拆下泵接头 (10) 。
- 拆下 O 形密封圈 (12) 。
Show/hide table
 | |
| 图 4 | g01440200 |
- 拆下惰轮 (13) 。
Show/hide table
 | |
| 图 5 | g01440207 |
- 从泵接头 (10) 上拆下轴承外圈 (14) ，拆下轴承外圈 (15) 。
Show/hide table
 | |
| 图 6 | g01440212 |
Show/hide table
 | |
| 图 7 | g01440213 |
- 从惰轮 (13) 上拆下轴承 (16) 。
Show/hide table
 | |
| 图 8 | g01440228 |
Show/hide table
 | |
| 图 9 | g01440229 |
- 从惰轮 (13) 上拆下密封圈 (17) 和轴承 (18) 。
Caterpillar Information System:
2007/12/24 An Improved Method of Mounting the Air Compressor Is Now Used {1803}
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 1170 - FMI 04
3516C Generator Set Engine Air Shutoff - Test
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 1170 - FMI 02
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 1169 - FMI 02
2008/01/01 An Improved Three-Piece Oil Pan Gasket is Now Used {1302, 7555}
2008/01/07 An Improved Three-Piece Oil Pan Gasket is Now Used {1302, 7555}
C175-16 Engine for 795F Series AC Off-Highway Trucks Connecting Rod - Type 1
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 1168 - FMI 04
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 1168 - FMI 03
2008/01/21 A New Lubricator for the Air Starting Motor is Now Used {1451}
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 1167 - FMI 04
TH55-E70 and TH55-E90 Petroleum Transmissions Gear Pump (Torque Converter and Transmission) - Install
C7 and C9 On-highway Engines Monitoring System - Additional Information for Caterpillar Model Year 2008 On-highway Engines Regulated by the California Air Resources Board
C13T-TH35 and C15T-TH35 Petroleum Packages Monitoring System - Additional Information for Caterpillar Model Year 2008 On-highway Engines Regulated by the California Air Resources Board
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 1170 - FMI 08
G3600 Engines Cylinder Combustion - Test
3500B Engines for Caterpillar Built Power Modules with the ADEM 3 Electronic Control Module Sensor Supply - Test
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) AL Fault Code
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) SP Fault Code
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Troubleshooting Dedicated Shutdown Indicators
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Indicator for Emergency Stop
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Indicator for High Water Temperature
TH55-E70 and TH55-E90 Petroleum Transmissions Gear Pump (Torque Converter and Transmission) - Disassemble