Hydraulic System Oil Filter (Winch) - Replace - If Equipped
Note: The Hystat transmission and the hydraulic system use a common tank.
- Two hydraulic filters are located on the right side of the machine. Open the access door on the right side of the machine.
Show/hide table
Illustration 2 g03804058 Some components are removed for clarity - Remove the winch filter elements by using the following steps.
- Place a pan under the filter.
- Remove the drain plug. Then, loosen the filter housing with a strap type wrench to allow air entry into the filter housing to allow for oil drainage.
- Allow some time for complete drainage of oil from the filter housing.
- Remove the filter housing from the oil filter base.
- Clean the filter element mounting base. Remove any part of the filter element gasket that remains on the filter element mounting base.
- Replace a new filter element into the housing. Apply a light coat of oil to the gasket of the new filter element.
- Install the filter housing onto the filter base. When the gasket contacts the filter element mounting base, tighten the housing to a torque of
40 ± 5 N·m (30 ± 4 lb ft) . Use a32 mm (1.25 inch) box end wrench. - Install the drain plug. Tighten to a torque of
12.5 ± 2.5 N·m (9.2 ± 1.8 lb ft)
Show/hide tableIllustration 3 g03803970 - Maintain the hydraulic oil level so the oil is visible in the sight gauge . Add oil, if necessary.
Reference: See Operation and Maintenance Manual, "Hydraulic System Oil Level - Check" for additional information.
Show/hide tableIllustration 4 g03803895 - Inspect the gasket on the hydraulic oil filler cap for damage. Replace the gasket, if necessary.
- Install the cap.
- Close the access door.
Show/hide table
Illustration 1 | g06206496 |
Caterpillar Information System:
D6K Track-Type Tractor Hydraulic System Oil - Change
D6K Track-Type Tractor Front Idler Position - Check/Adjust
992K Wheel Loader General Information (Power Train System)
D6K Track-Type Tractor Tracks
Engine Shutdown Procedure on Certain C4.4 Machine Engines {108I, 108U} Engine Shutdown Procedure on Certain C4.4 Machine Engines {108I, 108U}
Instructions for Sorting and Replacing HVAC Actuators {1800, 7320} Instructions for Sorting and Replacing HVAC Actuators {1800, 7320}
New One Piece Starter Housing is Used on Certain 824K, 825K, and 826K Machines {1453} New One Piece Starter Housing is Used on Certain 824K, 825K, and 826K Machines {1453}
D6K2 Track-Type Tractor Machine Systems Hydraulic Tank - Remove and Install
D6K Track-Type Tractor Fuel System - Prime
D6K Track-Type Tractor Backup Alarm
D6K Track-Type Tractor Backup Alarm - Test
320 GC, 320 and 323 Excavator Belt - Inspect/Adjust/Replace
Improved Hose Routing for the Hydraulic Discharge Screen Hose is now used on Certain D11T Track-Type Tractors {5068} Improved Hose Routing for the Hydraulic Discharge Screen Hose is now used on Certain D11T Track-Type Tractors {5068}
D6K Track-Type Tractor Leaving the Machine
D6K Track-Type Tractor Condenser (Refrigerant) - Clean
D6K Track-Type Tractor Cooling System Level - Check
986K Wheel Loader Steering Cylinder Bearings - Lubricate
992K Wheel Loader Features (Electronic Control System)
992K Wheel Loader Electronic Control (Power Train System)
Installation of the 530-2463 Coupler Lines Gp on Certain Wheel Loaders {5057, 5133} Installation of the 530-2463 Coupler Lines Gp on Certain Wheel Loaders {5057, 5133}
D6K Track-Type Tractor Equalizer Bar Center Pin - Lubricate
D6K Track-Type Tractor Fuel System - Fill
D6K Track-Type Tractor Fuel Tank Cap Filter and Strainer - Replace/Clean
992K Wheel Loader Location of Components (Power Train System)