Equalizer Bar - Disassemble
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 136-1452 | Internal Tip Pliers | 1 |
| B | 6V-3160 | Hydraulic Cylinder Gp | 1 |
| 350-7768 | Electric Hydraulic Pump (115V) | 1 | |
| 350-7769 | Electric Hydraulic Pump (230V) | ||
| 9U-5267 | Puller Stud | 1 | |
| 2J-3507 | Nut | 1 | |
| 3K-5234 | Hard Washer | 1 | |
| 6V-2098 | Press Sleeve | 1 | |
| FT2802 | Plate | 1 | |
| C | 350-7768 | Electric Hydraulic Pump Gp (115V) | 1 |
| 350-7769 | Electric Hydraulic Pump Gp (230V) | ||
| 6V-3175 | Hydraulic Cylinder Gp | 1 | |
| 4C-9634 | Puller Stud | 1 | |
| 9U-6832 | Nut | 1 | |
| 4K-0684 | Hard Washer | 1 | |
| 6V-4035 | Sleeve | 1 | |
Start By:
- Remove the equalizer bar.
Show/hide table
 |
|
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death. |
Show/hide table
| NOTICE |
|---|
|
Do not use threaded rods that have not been hardened as tooling with hydraulic cylinders. The maximum rated tonnage should be stamped on one end of the puller studs. Do not use threaded rods that have not been stamped with the rated tonnage. |
- Remove spacers (5) and seals (6) from equalizer bar (1).
- Remove plug (2), O-ring seal (3), and fitting (4) from each end of equalizer bar (1).
- Remove seals (8) from each end of equalizer bar (1).
- Use Tooling (A) to remove retaining rings (7) from each end of equalizer bar (1).
Show/hide table
Illustration 2 g01261042 - Use Tooling (B) to remove bearing (9) from each end of the equalizer bar.
Show/hide table
Illustration 3 g01261043 - Use Tooling (C) to remove center bearing (10) from the equalizer bar.
Show/hide table
| |
| Illustration 1 | g01261037 |
Caterpillar Information System:
Installation of Platform and Railings on D10T2 Track-Type Tractors {7150, 7256} Installation of Platform and Railings on D10T2 Track-Type Tractors {7150, 7256}
994K Wheel Loader Power Train Drive Shaft (Front) - Remove and Install
D6T Track Type Tractor Power Train Equalizer Bar - Remove and Install
Alarm and Protection Field Test Procedure for Certain Marine Engines {0374, 0599, 0706, 0708, 0709, 0769, 0781, 1000, 1408, 1439} Alarm and Protection Field Test Procedure for Certain Marine Engines {0374, 0599, 0706, 0708, 0709, 0769, 0781, 1000, 1408, 1439}
953K Track-Type Loader Machine Systems Hydraulic Tank - Remove and Install
Troubleshooting Procedure For Cat® Product Link (PL522) is Now Available For Certain Excavators in China {7606} Troubleshooting Procedure For Cat® Product Link (PL522) is Now Available For Certain Excavators in China {7606}
994K Wheel Loader Engine Supplement Valve Cover - Remove and Install
D6T Track-Type Tractor Electrohydraulic System Solenoid Valve - Test
D6T Track-Type Tractor Electrohydraulic System Transmission Clutch
D6T Track-Type Tractor Electrohydraulic System Transmission
854K Wheel Dozer Use of Wheel Chocks
D6T Track-Type Tractor Electrohydraulic System Power Train Oil Temperature Is High
637K Wheel Tractor-Scraper Plate Locations and Film Locations
Procedure to Install Third Function Hydraulic Kit and Third and Fourth Function Hydraulic Kit on Certain Series L and Series M Z Medium Wheel Loaders {0679, 1408, 5051, 5057, 5063, 5705, 7610, 7620} Procedure to Install Third Function Hydraulic Kit and Third and Fourth Function Hydraulic Kit on Certain Series L and Series M Z Medium Wheel Loaders {0679, 1408, 5051, 5057, 5063, 5705, 7610, 7620}
631K Original Equipment Manufacturer (OEM) Wheel Tractor Plate Locations and Film Locations
D8T Track-Type Tractor Undercarriage - Clean
Special Instruction for Installation of the Guardrail Arrangement on Certain D10T Track-Type Tractors {7150, 7256} Special Instruction for Installation of the Guardrail Arrangement on Certain D10T Track-Type Tractors {7150, 7256}
986K Wheel Loader Axle Oscillation Bearings - Lubricate
Installation Procedure for Cat® Health Onboard System on Certain Cat Machines {7605, 7610, 7620} Installation Procedure for Cat® Health Onboard System on Certain Cat Machines {7605, 7610, 7620}
986K Wheel Loader Diesel Exhaust Fluid Injector - Replace - Emission Related Component
D6T Track Type Tractor Power Train Equalizer Bar - Assemble
Correct Bolt Torque for the Fuel Filler Neck on Certain Compact Wheel Loaders {1273} Correct Bolt Torque for the Fuel Filler Neck on Certain Compact Wheel Loaders {1273}
986K Wheel Loader Fuel Tank Cap and Strainer - Clean
924K, 930K and 938K Wheel Loaders Cooling System Coolant Extender (ELC) - Add