D6T Track Type Tractor Power Train Caterpillar

Equalizer Bar - Remove and Install

Usage:

D6T 2B3

Removal Procedure

Show/hide table

Table 1
Required Tools
Tool	Part Number	Part Description	Qty
A	6V-4035	Sleeve	1
	6V-3160	Double Acting Cylinder	1
	5P-4776	Tool Stud	1
	1A-1935	Full Nut	1
	350-7768	Electric Hydraulic Pump Gp (115V)	1
B	8S-9906	Ratchet Puller	1
	1U-8823	Lifting Strap	3
	189-0410	Shackle As	1
	362-0960	Spreader Bar	1
C	504-9791	Lift Gp (60Hz)⁽¹⁾	2
	OR
	504-9793	Lift Gp (50Hz)⁽²⁾	2
D	4C-6486	Stand	2
	8S-7621	Tube	2
	8S-8048	Saddle	2
	8S-7615	Pin	2
E	350-7768	Electric Hydraulic Pump Gp (115V)	1
	6V-3160	Double Acting Cylinder	1
	5P-7288	Sleeve	1
	9u-5343	Puller Stud	1
	9u-5345	Nut	1
	8T-4167	Hard Washer	1

Show/hide table

⁽¹⁾	High-Voltage (480V) Low-Voltage (240V)
⁽²⁾	High-Voltage (400V) Low-Voltage (200V)

Start By:

Remove the center and rear bottom guards.

Show/hide table




Illustration 1	g00867666

Align sprocket segment (1) with the idler on the right side of the machine. Remove nuts (2) and the bolts. Remove sprocket segment (1). This procedure will allow the roller frame to pivot when the front of the machine is raised.
Show/hide table

Illustration 2 g01218846
Lift the blade assembly and install Tooling (D).
Show/hide table

Illustration 3 g06275579
Position Tooling (C) as shown in Illustration 3 and raise the machine. Place a 152 mm (6.0 inch) block under the left track. Lower the machine on the block until the weight is removed from the equalizer bar pins. Refer to Tool Operating Manual, NEHS1303 for more information on Tooling (C).
Show/hide table

Illustration 4 g01218648

Show/hide table

Illustration 5 g02355097
Use Tooling (B) and a suitable lifting device to support both ends of equalizer bar (3). The weight of equalizer bar (3) is approximately 102 kg (225 lb) to 259 kg (570 lb).
Show/hide table

Illustration 6 g02355039
Remove bolts (4), guards (5), and pin (6). Repeat this step for the opposite side of the equalizer bar.
Show/hide table

Illustration 7 g02355119
Disconnect hose assembly (7) and remove the fitting. Repeat this step for the opposite side.
Show/hide table

Illustration 8 g02355122
Remove bolt (8), the washer, and the spacer.
Use Tooling (E) to remove center pin (9).
Show/hide table

Illustration 9 g06267619
Use Tooling (C) to raise the machine for removal of the equalizer bar. Refer to Tool Operating Manual, NEHS1303 for more information on Tooling (C).
Show/hide table

Illustration 10 g02355156

Show/hide table

Illustration 11 g02355158
Use Tooling (B) to raise the left side of equalizer bar (3). Lower the right side of equalizer bar (3) until the right side of equalizer bar (3) will clear the frame.
Lower the left side and remove equalizer bar (3).