Track Roller Frame (Front) - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 504-9791 | Lift Gp (60Hz)(1) | 1 |
OR | |||
504-9793 | Lift Gp (50Hz)(2) | 1 | |
B | 1U-7498 | Support Stand As | 1 |
1U-7501 | Extension Tube | 1 | |
C | 8S-7610 | Base As | 1 |
8S-7650 | Cylinder As | 1 | |
447-0910 | Electric Hydraulic Pump Gp (115V) | 1 | |
447-0911 | Electric Hydraulic Pump Gp (230V) | ||
D | 1U-9895 | Crossblock | 1 |
8T-0360 | Bolt | 2 | |
8T-3282 | Hard Washer | 2 | |
5B-9603 | Bolt | 2 | |
E | 142-8548 | Lifting Bracket | 1 |
5P-8622 | Shackle | 2 |
Show/hide table
(1) | High-Voltage (480V) Low-Voltage (240V) |
(2) | High-Voltage (400V) Low-Voltage (200V) |
Start By:
- Separate the track.
- Remove the bulldozer and C-frame.
- Remove trunnion.
- Use Tooling (C) to raise the rear of the machine. Raise the machine so the roller frame will clear the track. Install Tooling (B).
Show/hide table
Illustration 2 g06267154 Typical example - Position Tooling (A) as shown. Use Tooling (A) to raise the front of the machine. Refer to Tool Operating Manual, NEHS1303, "Lift Group (Stand - 25 Ton)" for more information.
Show/hide table
Illustration 3 g02353977 - Remove hand rail (1).
Show/hide table
Illustration 4 g02354409 - Remove plug (2). Use Tooling (D) to remove plate (3) and the O-ring seal.
Show/hide table
Illustration 5 g00867141 - Use a suitable lifting device and a chain to apply some lifting force to track roller frame (4).
Show/hide table
Illustration 6 g02354117 - Remove nuts (5) and the washers. Remove bolts (7) and the guards (6). Lower the track roller frame (4)
8 cm (3 inches) .Show/hide tableIllustration 7 g02354356 - Attach a suitable lifting device to Tooling (E), as shown.
Show/hide table
Illustration 8 g00867145 - Remove and discard bolts (8). Remove retainer (9) and the O-ring seal.
Show/hide table
Illustration 9 g01219536 - Use Tooling (E) to remove track roller frame (4). The weight of track roller frame (4) is approximately
1860 kg (4100 lb) .Show/hide tableIllustration 10 g02354363 - Remove seal (10) from pivot shaft (11).
Show/hide table
Illustration 1 | g00867135 |
- Install track roller frame (4) in the reverse order of removal.
- Install new bolts (8). Tighten bolts (8) to a torque of
300 ± 40 N·m (220 ± 30 lb ft) .
- Install new bolts (8). Tighten bolts (8) to a torque of
Caterpillar Information System:
994K Wheel Loader Power Train Drive Shaft (Center) - Remove and Install
992K Wheel Loader Use of Wheel Chocks
C13 Engines for Caterpillar Built Machines Exhaust Temperature Is High
980L Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Piston Pump (Brake, Pilot, Fan)
980L Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Main Control Valve
953K Track-Type Loader Power Train Track Roller Frame - Remove and Install
980L Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Electronic Control (Hydraulic System)
910K and 914K Compact Wheel Loaders Mirror
992K Wheel Loader Mirror
992K Wheel Loader Alternate Exit
C4.4 and C6.6 Engines Exhaust Has Excessive White Smoke
953K Track-Type Loader Power Train Recoil Spring - Remove and Install
854K Wheel Dozer Alternate Exit
C13 Engines for Caterpillar Built Machines Engine Stalls at Low RPM
D6T Track-Type Tractor Electrohydraulic System Machine Movement
D6T Track-Type Tractor Electrohydraulic System Diagnostic Trouble Codes
D6T Track-Type Tractor Electrohydraulic System Power Train Oil Contains Air
D6T Track-Type Tractor Electrohydraulic System Power Train Oil Temperature Is High
854K Wheel Dozer Use of Wheel Chocks
D6T Track-Type Tractor Electrohydraulic System Transmission
D6T Track-Type Tractor Electrohydraulic System Transmission Clutch
D6T Track-Type Tractor Electrohydraulic System Solenoid Valve - Test
994K Wheel Loader Engine Supplement Valve Cover - Remove and Install
Troubleshooting Procedure For Cat® Product Link (PL522) is Now Available For Certain Excavators in China {7606} Troubleshooting Procedure For Cat® Product Link (PL522) is Now Available For Certain Excavators in China {7606}