C3.3 Industrial Engine Caterpillar

Cylinder Head

Usage:

C3.3 E3K

The cylinder head bolts are two different lengths. The following information provides the proper torque for the cylinder head bolts.

Show/hide table




Illustration 1	g01017007
The tightening sequence

Lubricate the threads and the underside of the head bolts with clean engine oil.

Tighten the bolts in the sequence that is shown in illustration 1 to the following torque. ... 50 N·m (37 lb ft)

Tighten the bolts again to the following torque. ... 100 N·m (74 lb ft)

Show/hide table




Illustration 2	g00905621
Head bolts

The head bolts require an additional torque turn procedure. The numbers (1, 3, 4) are three long cylinder head bolts. All the other bolts are short bolts. The tightening sequence is shown in illustration 1.

Place an index mark on the top of each bolt head. Tighten the short bolts for the additional amount. ... 225 degrees

Place an index mark on the top of each bolt head. Tighten the long bolts for the additional amount. ... 270 degrees

Thickness of the cylinder head ... 117.95 to 118.05 mm (4.643 to 4.647 inch)

Minimum thickness of cylinder head ... 117.20 mm (4.614 inch)

The maximum distortion of the cylinder head is given in table 1.

Show/hide table




Illustration 3	g01017008
Cylinder head

Show/hide table

Table 1
Dimension	Maximum Permissible Distortion
Width (A)	0.03 mm (0.0012 inch)
Height (B)	0.05 mm (0.0019 inch)
Diagonal Line (C)	0.05 mm (0.0019 inch)

Caterpillar Information System:

C6.6 Engines for Caterpillar Built Machines Electronic Unit Injector - Remove

C3.3 Industrial Engine Piston Height - Inspect

C3.3 Industrial Engine Connecting Rod - Inspect

C3.3 Industrial Engine Cooling System - Test

C3.3 Industrial Engine Cooling System - Inspect

C3.3 Industrial Engine Cooling System - Check - Overheating

C3.3 Industrial Engine Increased Engine Oil Temperature - Inspect

C3.3 Industrial Engine Excessive Engine Oil Consumption - Inspect

C3.3 Industrial Engine Excessive Bearing Wear - Inspect

C1.7, C1.8, and C2.4 Tier 4 Interim and EU Stage 3A Engines for Caterpillar Built Machines Engine Oil Pump - Inspect

C3.3 Industrial Engine Engine Oil Pressure - Test

C3.3 Industrial Engine Valve Guide - Inspect

345D, 349D and 349D2 Excavators Fuel System Secondary Filter - Replace

345D, 349D and 349D2 Excavators Fuel System Primary Filter (Water Separator) Element - Replace

2010/05/06 Valve Bridges are Included with Cylinder Heads {1102, 1123}

2010/08/23 Valve Bridges are Included with Cylinder Heads {1102, 1123}

2009/09/01 Valve Bridges are Included with Cylinder Heads {1102, 1123}

3176C, 3406E and 3456 Industrial Engines ECM - Replace

Causes of a 3002-2 Diagnostic Code for Some G3512 and G3516 Engines{1408, 1900, 191N, 7400} Causes of a 3002-2 Diagnostic Code for Some G3512 and G3516 Engines{1408, 1900, 191N, 7400}

C13, C15, and C18 Tier 4 Final Engines Engine Oil Pan

G3408C and G3412C Engines Safety Messages

C7 and C9 On-Highway Engines Engine Cranks but Does Not Start

C7 and C9 On-Highway Engines Engine Misfires, Runs Rough or Is Unstable

G3520B Industrial Engines Engine Monitoring System