Specifications
Show/hide table
Illustration 1 | g03378942 |
Relief valve locations (1) Main relief valve (2) Boom cylinder line (head end) (3) Boom cylinder line (rod end) (4) Stick cylinder line (head end) (5) Stick cylinder line (rod end) (6) Bucket cylinder line (head end) (7) Bucket cylinder line (rod end) (8) Swing (right) (9) Swing (left) (10) Left travel crossover relief valve for forward travel (upper valve) (11) Left travel crossover relief valve for reverse travel (lower valve) (12) Right travel crossover relief valve for forward travel (upper valve) (13) Right travel crossover relief valve for reverse travel (lower valve) (14) Pilot relief valve (15) Main control valve (16) Pilot filter (17) Travel motor (right) (18) Travel motor (left) (19) Swing motor |
Show/hide table
Relief Valve | Specifications | Torque for Locknut | ||
---|---|---|---|---|
New
Rebuilt(1) |
Service Limit(2) | |||
Main relief valve | |
|
|
|
(Heavy Lift) |
|
|
||
Boom cylinder line (head end) | |
≥ |
|
|
Boom cylinder line (rod end) | |
≥ |
||
Stick cylinder line (head end) | ||||
Stick cylinder line (rod end) | |
≥ |
||
Bucket cylinder line (head end) | |
≥ |
||
Bucket cylinder line (rod end) | ||||
Swing relief pressure (right) | |
|
|
|
Swing relief pressure (left) | ||||
Left travel crossover relief valve (forward) | |
≥ |
|
|
Left travel crossover relief valve (reverse) | ||||
Right travel crossover relief valve (forward) | ||||
Right travel crossover relief valve (reverse) | ||||
Pilot relief valve | |
|
Show/hide table
(1) | A New specification is the performance that can be expected for a new machine. A “Rebuild” specification is the performance that can be expected after rebuilding the components of a system. |
(2) | Performance beyond “Service Limit” specifications is an indication of the following problems: improper adjustment, wear, damage of relief valves and damage of pumps. |
Show/hide table
Relief Valves | Pressure change With One Turn Of Adjustment Screw |
---|---|
Main valves | |
Line relief valve | |
Swing relief valve | |
Travel crossover relief valve | |
Pilot relief valve | |
Note: Pressure values in Table 2 are approximate values. Use a pressure gauge for adjustment.
Note: Normal operations of the engine and pumps are necessary for the pressure adjustments. If the results of the pressure adjustment are not correct, then check the engine and the pump characteristic curve. Slow output flow from the pump is an indication of air in the hydraulic system. Make sure that no air is present in the hydraulic system. Refer to Testing and Adjusting, "Main Hydraulic Pump Air - Purge".
Caterpillar Information System:
340F Excavator Machine Systems Gear Pump (Pilot) - Test
340F Excavator Machine Systems Pump Control (Output Flow) - Adjust
340F Excavator Machine Systems Main Pump (Flow) - Test - Hydraulic Power
340F Excavator Machine Systems Relief Valve (Crossover) - Test and Adjust
340F Excavator Machine Systems Travel Motor - Test - Measurement of Case Drain Oil
340F Excavator Machine Systems Swing Bearing Movement - Measure
340F Excavator Machine Systems Relief Valve (Swing) - Test and Adjust
340F Excavator Machine Systems Swing Motor - Test - Measurement of Case Drain Oil
Improve Clearance Adjustment Procedure Between Hose And Damper Of Certain D6R Track-Type Tractors {1380} Improve Clearance Adjustment Procedure Between Hose And Damper Of Certain D6R Track-Type Tractors {1380}
D5R and D6N Track-Type Tractor Machine Systems Refrigerant Condenser Fan and Fan Motor - Remove and Install
980M and 982M Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Piston Pump Cutoff Pressure (Hydraulic Fan) - Test and Adjust
973K Track Type Loader Radiator Core - Clean
340F Excavator Machine Systems Joystick and Pedal - Calibrate
D5R and D6N Track-Type Tractor Power Train Main Drive Shaft - Remove and Install
340F Excavator Machine Systems Accumulator (Swing) - Test and Charge
D10T2 Fan Pump Update {1387, 5070} D10T2 Fan Pump Update {1387, 5070}
340F Excavator Machine Systems Pump Control (Negative Flow) - Test
340F Excavator Machine Systems Pump Control (Negative Flow) - Adjust
340F Excavator Machine Systems Pump Control (Output Flow) - Test - One Pump Calibration (Optional Test)
340F Excavator Machine Systems Relief Valve (Pilot) - Test and Adjust
980L Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Steering Control - Control System
980M and 982M Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Piston Pump Margin Pressure (Hydraulic Fan) - Test and Adjust
854K Wheel Dozer Windows - Clean
Reference Guide for a Proper Failure Analysis by CAT Dealer {0374, 1000} Reference Guide for a Proper Failure Analysis by CAT Dealer {0374, 1000}