Thermostatic Valve - Inspect
Perform the following procedure:
- Prior to inspecting the electronic thermostat, remove connector (2) to disconnect power to the controller module.
Show/hide table
Illustration 2 g02718645 Component breakdown for inspection of the electronic thermostat for moisture entry
(1) Motor cover
(2) Control module
(3) Motor group
(4) Motor mount assembly - Remove the four bolts from motor cover (1). Remove the cover from the motor group.
- Disconnect the connector from control module (2). Remove the mounting bolts, washers, and spacers from the control module. Remove the control module from the electronic thermostat.
- Remove the four bolts and washers from motor (3). Remove the motor from motor mount assembly (4).
- Visually inspect the motor housing for moisture entry, corrosion, and rust. Turn the armature of the motor to ensure that the motor turns freely.
If moisture entry, corrosion, or rust is found inside the motor housing, or if the motor does not turn freely, replace the motor. Shuttling the thermostatic valve from end to end should require 45 to 46 turns. The shaft rotation should be smooth. If shuttling the valve is not within the specified number of turns or if the shaft rotation is not smooth, replace the motor.
Note: For additional information, refer to Special Instructions, REHS7404.
- Perform steps 4 through 2 to assemble the electronic thermostat and motor assembly.
Show/hide table
| |
| Illustration 1 | g01320751 |
Caterpillar Information System:
631K OEM Power Train Service and Parking Brake - Assemble
AD55 Underground Articulated Truck Steering System Steering System (Pilot Oil)
Wear Guidelines for Compact Track Loaders {4180} Wear Guidelines for Compact Track Loaders {4180}
C175-16 and C175-20 Locomotive Engines Fuel Lines - Install - High Pressure
988K XE Wheel Loader Lifting and Tying Down the Machine
3500E EPA Tier 4 Final and IMO-II/III Switchable Marine Engines Crankshaft
3500E EPA Tier 4 Final and IMO-II/III Switchable Marine Engines Camshaft
631K OEM Power Train Service and Parking Brake - Disassemble
980M and 982M Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Steering Time - Check
C175-16 and C175-20 Locomotive Engines Fuel Control Valve - Remove and Install
980M and 982M Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Service Brake System Pressure - Test
980M and 982M Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Service Brakes - Test
D5R and D6N Track-Type Tractor Machine Systems Bottom Guard - Remove and Install
980L Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Variable Pitch Fan System
631K OEM Power Train Bearing Cage (Drive Shaft) - Disassemble
Repair Procedure For Sealing Air Conditioner On Certain D5, D6, D7, and D8 Track-Type Tractors {7309, 7311, 7316, 7320} Repair Procedure For Sealing Air Conditioner On Certain D5, D6, D7, and D8 Track-Type Tractors {7309, 7311, 7316, 7320}
D5R and D6N Track-Type Tractor Engine Supplement Valve Cover - Remove and Install
631K OEM Power Train Bearing Cage (Drive Shaft) - Assemble
988K XE Wheel Loader Declaration of Conformity
D5R and D6N Track-Type Tractor Power Train Final Drive Planetary Carrier (In Chassis) - Remove and Install
988K XE Wheel Loader Cooling System Coolant (ELC) - Change
988K XE Wheel Loader Cooling System Coolant Extender (ELC) - Add
980M and 982M Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Position Sensor (Lift Linkage) - Replace
988K XE Wheel Loader Cooling System Coolant Level - Check