Cylinder Block
Show/hide table
| |
| Illustration 1 | g06060440 |
|
Rear view of engine | |
Show/hide table
| Specification for 456-6318 Cylinder Block Gp | |||
|---|---|---|---|
| Item | Qty | Part | Specification Description |
| - | During assembly, bottom of the plate, top of the block, and both the sides of the gasket plate must be free of all visible fuel, oil, water and gasket adhesives, assembly compounds, or any other contaminates. | ||
| A | 32 | 8T-0099 Dowel | Extension of the dowel from the top face of the cylinder block is |
| 1 | 2 | 5F-9657 O-Ring Seal | Lubricate the bore lightly with the lubricant that is being sealed. |
| C | 16 | 197-7008 Dowel | Extension of the dowel from the top face of the cylinder block is |
| 2 | 18 | 101-1198 Camshaft Bearing | All centerlines through oil holes in the camshaft bearings and the camshaft bearing junctions must be positioned as shown in Illustration 1 on each side of cylinder block. |
| Oil holes must be positioned from horizontal at an angle (D) of 20 ± 5 degrees as shown in Illustration 1. | |||
| Bore in the cylinder block for camshaft bearing is |
|||
| E | 9 | 223-1696 Crankshaft Bearing Cap | Width of the crankshaft bearing cap is Width of cylinder block for main bearing cap is |
| 3 | 8 | 6V-3348 O-Ring Seal | Lubricate the bore lightly with the lubricant that is being sealed. |
| F | - | - | New dimension from centerline of crankshaft bearing bore to the top of the cylinder block is |
| G | - | - | New dimension from centerline of crankshaft bearing bore to bottom of cylinder block (pan rails) is |
| H | - | - | Bore in the cylinder block for the main bearings is |
Show/hide table
| |
| Illustration 2 | g03497817 |
|
Section B-B | |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| J | 1 | 7N-2047 Dowel | Extension of the dowel from the rear face of the cylinder block is |
| K | 2 | 7N-2047 Dowel | Extension of the dowel from the front face of the cylinder block is |
| L | 2 | 4N-0683 Dowel | Extension of the dowel from the rear face of the cylinder block is |
| M | 2 | 7N-2044 Dowel | Extension of the dowel from the front face of the cylinder block is |
Show/hide table
| |
| Illustration 3 | g06060441 |
|
Front view | |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| 4 | 4 | 4W-4813 Plug | Torque to |
| 5 | 4 | 8T-2929 O-Ring Seal | During assembly, apply Krytox GPL-205 to secure O-rings. |
| 6 | 4 | 8T-2928 O-Ring Seal | Lightly lubricate the bore with 5P-3975 Rubber Lubricant. |
| 7 | 36 | 7X-7925 Bolt | Use the following procedure to tighten the crankshaft bearing cap bolts:
1. Before assembly, lubricate the threads completely with clean engine oil. 2. Hand tighten the bolts in the tapped holes. 3. Tighten the bolts in the numerical sequence as shown in Illustration 3 to 4. Again, tighten the bolts for an extra angle of 180 ± 5 degrees. |
Caterpillar Information System:
950M T3 and 962M T3 Wheel Loader Engine Supplement Electronic Control Module - Remove and Install
950M T3 and 962M T3 Wheel Loader Engine Supplement Oil Pan - Remove - Aluminum Oil Pan
3516E Engines for Caterpillar Built Machines Flywheel Housing
950M T3 and 962M T3 Wheel Loader Engine Supplement Oil Pan - Install - Aluminum Oil Pan
C1.7 and C2.2 Industrial Engines Engine Oil Lines
C1.7 and C2.2 Industrial Engines Exhaust Cooler (NRS)
3512E Tier 4 Final Engines for Land Electric Drilling Water Pump
950M T3 and 962M T3 Wheel Loader Engine Supplement Vibration Damper and Pulley - Install
950M T3 and 962M T3 Wheel Loader Machine System Counterweight - Remove and Install
950M T3 and 962M T3 Wheel Loader Engine Supplement Vibration Damper and Pulley - Remove
950M T3 and 962M T3 Wheel Loader Engine Supplement Fan Group (Includes Fan, Fan Guard, Fan Shroud, and Hydraulic Fan Motor) - Remove and Install
3516E Engines for Caterpillar Built Machines Engine Oil Pump
3516E Engines for Caterpillar Built Machines Engine Oil Scavenge Pump
988K XE Wheel Loader Braking System - Test
An Improved Link Assembly for Quick Coupler Is Now Used on Certain Wheel Loaders {6116, 6129} An Improved Link Assembly for Quick Coupler Is Now Used on Certain Wheel Loaders {6116, 6129}
950M T3 and 962M T3 Wheel Loader Engine Supplement Turbocharger - Install - First Stage Turbocharger
3516E Engines for Caterpillar Built Machines Engine Support (Front)
950M T3 and 962M T3 Wheel Loader Engine Supplement Turbocharger - Remove - First Stage Turbocharger
3516E Engines for Caterpillar Built Machines Vibration Damper Guard
C175–16 Locomotive Engine Turbocharger
3516E Engines for Caterpillar Built Machines Fuel Injector
3516E Engines for Caterpillar Built Machines Camshaft Bearing Position
New Modification to the Injector Harness Bracket on Certain D10T Track-Type Tractors {1120, 1408} New Modification to the Injector Harness Bracket on Certain D10T Track-Type Tractors {1120, 1408}
C175–16 Locomotive Engine Test Tools for the Electrical System