Vibration Damper and Pulley - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导向螺柱 M14 x1.5 x 100 mm |
1 |
B | 227-4393 | E18 Torx 套筒 | 1 |
C | 8T-3052 | 度数轮 | 1 |
D | - | 导向螺柱 M12 x1.75 x 50 mm |
2 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 确保曲轴适配器和曲轴前部清洁且无损坏。
- 检查减振器 (8) 有无损坏。 如有必要,更换减振器。
- 如有必要,按照步骤 3.a 至 3.e 将减振器、曲轴皮带轮安装到曲轴适配器上。
- 将曲轴适配器 (6) 放到适当的支承上。
- 将工具 (D) 安装到曲轴适配器 (6) 上。
- 将曲轴皮带轮 (7) 和减振器 (8) 安装到工具 (D) 上方。
- 将螺栓 (9) 安装到曲轴皮带轮组件上。
注: 在曲轴皮带轮组件周围等距离布置螺栓 (9)。
- 拧紧螺栓 (9) 至扭矩为
115 N·m (85 lb ft) 。
- 如有必要,安装摩擦片 (5)。 按照步骤4.a 至步骤 4.b 安装摩擦片 (5)。
- 安装摩擦片 (5)。
- 将新前油封安装到前盖上。 有关正确的步骤,请参阅拆解和组装, "曲轴前油封 - 拆卸和安装"。
- 将工具 (A) 安装在曲轴上。
Show/hide table
图 2 g06087768 - 将曲轴皮带轮组件 (4) 安装到曲轴上。
- 将一颗 Torx 螺钉 (3) 安装到曲轴皮带轮组件 (4) 上,用手拧紧。
- 拆下工具 (A)。
- 将其余 Torx 螺钉 (3) 安装到曲轴皮带轮组件 (4) 上。
- 使用适当的工具,使曲轴固定不动。 拧紧 Torx 螺钉 (3) 至扭矩为
40 N·m (29 lb ft) 。 - 使用工具 (B) 和 (C) 将 Torx 螺钉 (3) 再转动 120 度。
Show/hide table
图 3 g02725128 - 将支承 (2) 安装到位,然后松开机架组件 (1) 的支承。
Show/hide table
图 1 | g06087770 |
结束:
- 安装驱动皮带。
Caterpillar Information System:
950M T3 and 962M T3 Wheel Loader Machine System Counterweight - Remove and Install
950M T3 and 962M T3 Wheel Loader Engine Supplement Vibration Damper and Pulley - Remove
950M T3 and 962M T3 Wheel Loader Engine Supplement Fan Group (Includes Fan, Fan Guard, Fan Shroud, and Hydraulic Fan Motor) - Remove and Install
3516E Engines for Caterpillar Built Machines Engine Oil Pump
3516E Engines Crankshaft - Install
3516E Engines Crankshaft - Remove
3516E Engines for Caterpillar Built Machines Gear Group (Front)
986K Wheel Loader Operator Controls
340F Excavator Operator Controls
Installation of the 6A Bulldozer and Slope Assist on a D6T Track-Type Tractor {6050, 6052, 6060, 6701} Installation of the 6A Bulldozer and Slope Assist on a D6T Track-Type Tractor {6050, 6052, 6060, 6701}
Installation of the Variable Pitch, Angle, and Tilt Blade and Slope Assist on a D6T Track-Type Tractor {6050, 6052, 6060, 6701} Installation of the Variable Pitch, Angle, and Tilt Blade and Slope Assist on a D6T Track-Type Tractor {6050, 6052, 6060, 6701}
3516E Engines for Caterpillar Built Machines Accessory Drive (Upper Right Hand)
3512E Tier 4 Final Engines for Land Electric Drilling Water Pump
C1.7 and C2.2 Industrial Engines Exhaust Cooler (NRS)
C1.7 and C2.2 Industrial Engines Engine Oil Lines
950M T3 and 962M T3 Wheel Loader Engine Supplement Oil Pan - Install - Aluminum Oil Pan
3516E Engines for Caterpillar Built Machines Flywheel Housing
950M T3 and 962M T3 Wheel Loader Engine Supplement Oil Pan - Remove - Aluminum Oil Pan
950M T3 and 962M T3 Wheel Loader Engine Supplement Electronic Control Module - Remove and Install
3516E Engines for Caterpillar Built Machines Cylinder Block
3516E Engines for Caterpillar Built Machines Engine Oil Scavenge Pump
988K XE Wheel Loader Braking System - Test
An Improved Link Assembly for Quick Coupler Is Now Used on Certain Wheel Loaders {6116, 6129} An Improved Link Assembly for Quick Coupler Is Now Used on Certain Wheel Loaders {6116, 6129}
950M T3 and 962M T3 Wheel Loader Engine Supplement Turbocharger - Install - First Stage Turbocharger