Fuel System Filter (In-Line) - Replace
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Note: Replace the fuel filter before the scheduled interval if any of the following occur:
- The filter screen is more than half obstructed.
- Engine performance is poor.
- Open the access door at the back of the machine. The in-line fuel system filter is directly below the fuel tank. Refer to Operation and Maintenance Manual, "Access Doors and Covers".
Show/hide table
Illustration 1 g06043261 Show/hide table
Illustration 2 g03802698 - Close fuel shutoff valve (1).
- Loosen hose clamps.
- Remove in-line fuel filter (2) and discard the fuel filter.
- Replace in-line fuel filter (2). Ensure that the arrow on the filter points upward.
- Tighten hose clamps.
- Open fuel shutoff valve (1).
- Start the engine.
- Check for leaks.
- Close the rear access door.
Caterpillar Information System:
PL61 Pipelayer Window Wipers - Inspect/Replace
PL61 Pipelayer Window Washer Reservoir - Fill
New Method for Hystat Calibration without Raising the Machine on All 924K, 926M, 930K, 930M, 938K, and 938M Wheel Loaders {0374, 4350, 4350, 7490, 7610, 7620} New Method for Hystat Calibration without Raising the Machine on All 924K, 926M, 930K, 930M, 938K, and 938M Wheel Loaders {0374, 4350, 4350, 7490, 7610, 7620}
PL61 Pipelayer Track Roller Frame - Inspect
950M and 962M Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems General Information (Electronic Control System)
PL61 Pipelayer Track - Check/Adjust
PL61 Pipelayer Radiator Pressure Cap - Clean/Replace
PL61 Pipelayer Pivot Shaft Oil Level - Check
PL61 Pipelayer Hydraulic System Oil Filter (Winch) - Replace - If Equipped
PL61 Pipelayer Hydraulic System Oil Filter - Replace
PL61 Pipelayer Hydraulic System Oil - Change
631K Original Equipment Manufacturer (OEM) Wheel Tractor Hitch - Inspect
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit Pump Swash Plate - Health Check
A New Electronic Control Module (ECM) Cover Is Now Used For Certain C9.3 Machine Engines {1408} A New Electronic Control Module (ECM) Cover Is Now Used For Certain C9.3 Machine Engines {1408}
631K OEM Wheel Tractor Systems Hydraulic Accumulator
631K OEM Wheel Tractor Systems Hydraulic Accumulator
631K OEM Wheel Tractor Systems Hydraulic Accumulator
C13, C15, and C18 Tier 4 Final Engines Turbocharger
631K Wheel Tractor-Scraper Display and Camera - Clean - If Equipped
844K and 854K Wheel Dozers and 990K, 992K, 993K, 994F and 994H Wheel Loaders Powered Access Stairway General Information
631K Original Equipment Manufacturer (OEM) Wheel Tractor Battery or Battery Cable - Inspect/Replace
631K Original Equipment Manufacturer (OEM) Wheel Tractor Battery - Clean/Check
844K and 854K Wheel Dozers and 990K, 992K, 993K, 994F and 994H Wheel Loaders Powered Access Stairway Powered Stairway System
Improved Clam Shell Latch Linkage for Rear Hood Group Is Available for Certain Medium Wheel Loaders {7251, 7251} Improved Clam Shell Latch Linkage for Rear Hood Group Is Available for Certain Medium Wheel Loaders {7251, 7251}