Hydraulic System Oil Filter (Winch) - Replace - If Equipped
Note: The Hystat transmission and the hydraulic system use a common tank.
- Two hydraulic filters are on the right side of the machine. Open the access door on the right side of the machine.
Show/hide table
Illustration 2 g06047095 Some components are removed for clarity - Remove the winch filter elements by using the following steps.
- Place a pan under the filter.
- Remove the filter element with a strap type wrench.
- Clean the filter element mounting base. Remove any part of the filter element gasket that remains on the filter element mounting base.
- Apply a light coat of oil to each gasket of the new filter elements.
- Install the new filter element by hand. When the gasket contacts the filter element mounting base, tighten the filter element for an additional three quarters of a turn.
- Close the access door.
Show/hide table
Illustration 3 g03803970 - Maintain the hydraulic oil level so the oil is visible in the sight gauge . Add oil, if necessary.
Reference: See Operation and Maintenance Manual, "Hydraulic System Oil Level - Check" for additional information.
Show/hide table
Illustration 4 g03803895 - Inspect the gasket on the hydraulic oil filler cap for damage. Replace the gasket, if necessary.
- Install the cap.
- Close the access door.
Show/hide table
| |
| Illustration 1 | g06043038 |
Caterpillar Information System:
PL61 Pipelayer Hydraulic System Oil Filter - Replace
PL61 Pipelayer Hydraulic System Oil - Change
631K Original Equipment Manufacturer (OEM) Wheel Tractor Hitch - Inspect
PL61 Pipelayer Fuel System - Fill
Procedure to Install an Updated Harness Assembly for the Cushion Hitch on Certain 621K, 623K, and 627K Wheel Tractor Scrapers {1408} Procedure to Install an Updated Harness Assembly for the Cushion Hitch on Certain 621K, 623K, and 627K Wheel Tractor Scrapers {1408}
631K Original Equipment Manufacturer (OEM) Wheel Tractor Brake Pads - Check
PL61 Pipelayer Front Idler Position - Check/Adjust
PL61 Pipelayer Ether Starting Aid Cylinder - Replace
PL61 Pipelayer Engine Oil and Filter - Change
PL61 Pipelayer Engine Oil Sample - Obtain
PL61 Pipelayer Engine Oil Level - Check
PL61 Pipelayer Engine Crankcase Breather Filter - Replace
PL61 Pipelayer Pivot Shaft Oil Level - Check
PL61 Pipelayer Radiator Pressure Cap - Clean/Replace
PL61 Pipelayer Track - Check/Adjust
950M and 962M Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems General Information (Electronic Control System)
PL61 Pipelayer Track Roller Frame - Inspect
New Method for Hystat Calibration without Raising the Machine on All 924K, 926M, 930K, 930M, 938K, and 938M Wheel Loaders {0374, 4350, 4350, 7490, 7610, 7620} New Method for Hystat Calibration without Raising the Machine on All 924K, 926M, 930K, 930M, 938K, and 938M Wheel Loaders {0374, 4350, 4350, 7490, 7610, 7620}
PL61 Pipelayer Window Washer Reservoir - Fill
PL61 Pipelayer Window Wipers - Inspect/Replace
PL61 Pipelayer Fuel System Filter (In-Line) - Replace
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit Pump Swash Plate - Health Check
A New Electronic Control Module (ECM) Cover Is Now Used For Certain C9.3 Machine Engines {1408} A New Electronic Control Module (ECM) Cover Is Now Used For Certain C9.3 Machine Engines {1408}
631K OEM Wheel Tractor Systems Hydraulic Accumulator