- Engine:
- C13 (S/N: LEE1-UP)
- C15 (S/N: SDP1-UP)
Introduction
This Special Instruction provides information for the updates to the wires and the harness to the exhaust combustion groups on the Heavy-Duty 2007 engines.
Routing for the 289-2515 Exhaust Combustion Gp
Illustration 1 | g01371259 |
(1) 289-2515 Exhaust Combustion Gp |
Illustration 2 | g01371262 |
(2) 204-1611 Cable Strap (3) 3S-2093 Cable Strap (4) 3S-2093 Cable Strap |
- Use 204-1611 Cable Strap (2) in order to tie the sensor back to the line.
- Install the strap (3) to both connectors that are on the clip. Install the strap in the grooves of the body of the connector.
- Use 3S-2093 Cable Strap (4) to tie the excess wires of the sensor.
Illustration 3 | g01371264 |
(5) 290-1993 Cable Strap |
Install the strap (5) to the main leg of the harness at the locations that are shown in Illustration 3.
Illustration 4 | g01371268 |
(6) 204-1611 Cable Strap (7) Tube |
Use strap (6) to tie the sensor to the tube (7).
Illustration 5 | g01371278 |
Approximate orientation of the sensor probe and the boot (8) . |
Illustration 6 | g02586360 |
(9) 3S-2093 Cable Strap |
Attach strap (9) to the existing clip (10) .
Updating 289-2724 Exhaust Combustion Gp
Illustration 7 | g01371285 |
(1) 289-2724 Exhaust Combustion Gp |
Illustration 8 | g01371288 |
(2) Strap (3) Clip (4) 3S-2093 Cable Strap (5) 290-1993 Cable Strap (6) 285-6393 Clip |
- Install strap (2) to both connectors on the clip (3) with the strap in the groove of the body of the connector.
- Use strap (4) to tie the excess wire from the sensor.
- Install strap (5) and clip (6).
Illustration 9 | g01371292 |
(7) 277-1873 Clip (8) 9M-1974 Hard Washer (9) 5P-7970 Nut (10) 3S-2093 Cable Strap (11) 206-6875 Tube Cap (12) 4P-7428 Clip (13) 5P-8245 Hard Washer (14) 8T-0293 Bolt (15) 3S-2093 Cable Strap (16) 132-5789 Clip (17) 3S-2093 Cable Strap |
Refer to Illustration 9 for the location of the straps and hardware.
Illustration 10 | g01371294 |
(18) 290-1993 Cable Straps |
Refer to Illustration 10 in order to install the straps.
Illustration 11 | g02585779 |
(19) 204-1611 Cable Strap (21) 3S-2093 Cable Strap |
- Install the strap (19). Install the strap to the sensor and back to the line (20) .
- Install the strap (21) to the existing clip (22) .
Updating 289-2841 Exhaust Combustion Gp
Illustration 12 | g01371299 |
(1) 289-2841 Exhaust Combustion Gp |
Illustration 13 | g01371304 |
(2) 204-1611 Cable Straps (3) 3S-2093 Cable Strap (4) 285-6395 Clip (5) 290-1993 Cable Strap |
Use two straps (2) to tie the sensor back to the line.
Install strap (3) to both of the connectors on the clip. Install the strap with the strap in the groove of the connector.
Install the clip (4) and the strap (5) that is shown in Illustration 13.
Illustration 14 | g01371306 |
(6) 277-1873 Clip (7) 9M-1974 Hard Washer (8) 5P-7970 Nut (9) 3S-2093 Cable Strap (10) 206-6875 Tube Cap (11) 4P-7428 Clip (12) 5P-8245 Hard Washer (13) 8T-0293 Bolt (14) 3S-2093 Cable Strap (15) 4P-7428 Clip (16) 3S-2093 Cable Strap |
Install the hardware that is shown in Illustration 12.
Illustration 15 | g02585916 |
(17) 204-1611 Cable Strap (18) 295-6240 Wire (19) 6V-8212 Bolt (20) 6V-5839 Washer (21) 290-1993 Cable Strap |
Install strap (17). Tie the strap to the spark plug wire (18) to the tube.
Note: Include the spark plug wire in the clip that is above the CGI cooler.
Updating 289-2734 Exhaust Combustion Gp
Illustration 16 | g02586056 |
(1) 289-2734 Exhaust Combustion Gp |
Illustration 17 | g01371310 |
(2) 204-1611 Cable Strap (3) 3S-2093 Cable Straps (4) 3S-2093 Cable Strap |
Install strap (2) to the tube.
Install two straps (3). ensure that the straps are in the groove of the body of the connector.
Secure the excess wire with strap (4).
Illustration 18 | g01371312 |
(5) 285-6395 Clip (6) 9M-1974 Hard Washer (7) 6V-8189 Nut (8) 3S-2093 Cable Strap (9) 110-8330 Spacer (10) 5M-2894 Hard Washer (11) 1A-5964 Bolt (12) 285-6395 Clip (13) 290-1993 Cable Strap |
Install the hardware that is shown in Illustration 18.
Illustration 19 | g02586159 |
(14) 285-6393 Clip (15) 5M-2894 Hard Washer (16) 0T-0102 Bolt (17) 290-1993 Cable Strap (18) 197-6453 Bracket As (19) 5M-2894 Hard Washer (20) 1B-2878 Nut (21) 285-6395 Clip (22) 6V-6317 Bolt (23) 6V-6317 Bolt (24) 290-1993 Cable Strap |
Install the hardware that is shown in Illustration 19.
Illustration 20 | g02586179 |
(25) 285-6393 Clip (26) 290-1993 Cable Strap |
Ensure that clip (25) is bent toward the block.
Illustration 21 | g02586187 |
(27) 285-6395 Clip (28) 290-1993 Cable Strap (29) 4P-7581 Clip (30) 5M-2894 Hard Washer (31) 0T-0102 Bolt (32) 3S-2093 Cable Strap |
Updating 289-2744 Exhaust Combustion Gp
Illustration 22 | g01371318 |
(1) 289-2744 Exhaust Combustion Gp |
Illustration 23 | g01371320 |
(2) 204-1611 Cable Strap (3) 3S-2093 Cable Strap (4) 3S-2093 Cable Strap |
Install strap (2) to the tube.
Secure excess wire from the sensor with strap (3) .
Install strap (4) on the existing clips. Install the strap in the groove of the body of the connector.
Illustration 24 | g01371322 |
(5) 285-6395 Clip (6) 9M-1974 Hard Washer (7) 6V-8189 Nut (8) 3S-2093 Cable Strap |
Install the hardware that is shown in Illustration 24.
Illustration 25 | g01371325 |
(9) 285-6393 Clip (10) 8T-4896 Hard Washer (11) 0L-1351 Bolt (12) 290-1993 Cable Strap |
Install the hardware that is shown in Illustration 25.
Note: Ensure that clip (9) is bending toward the block.
Illustration 26 | g02586276 |
(13) 295-6239 Wire (14) 285-6393 Clip (15) 290-1993 Cable Strap (16) 285-6393 Clip (17) 290-1993 Cable Strap |
Note: Install clip (16) at a 45 degree angle from the vertical under the bolt. Ensure that the clip is bent toward the engine block.
Install the hardware that is shown in Illustration 26.
Note: Ensure that clip (14) is bending away from the block.
Note: Install clip (16) at a 45 degree angle from vertical under the bolt.
Illustration 27 | g01371329 |
(18) 3S-2093 Cable Strap (19) 4P-7581 Clip (20) 8T-4896 Hard Washer (21) 0L-1351 Bolt (22) 3S-2093 Cable Strap |
Install strap (18) to the existing clip.
Ensure that the clip (19) is bent toward the block.
Updating 289-2752 Exhaust Combustion Gp
Illustration 28 | g01371331 |
(1) 289-2752 Exhaust Combustion Gp |
Illustration 29 | g01371333 |
(2) 204-1611 Cable Strap (3) 3S-2093 Cable Strap (4) 3S-2093 Cable Strap |
Install two straps (2) to the tube.
Install straps (3). Install the straps in the groove of the body of the connectors.
Secure excess wire from the sensor with strap (4).
Illustration 30 | g01371335 |
(5) 285-6395 Clip (6) 9M-1974 Hard Washer (7) 6V-8189 Nut (8) 3S-2093 Cable Strap (9) 206-6875 Tube Cap (10) 290-1993 Cable Strap |
Install the hardware that is shown in Illustration 30.
Illustration 31 | g02586437 |
(11) 290-1993 Cable Strap (12) 285-6395 Clip (13) 290-1993 Cable Strap |
Note: Install clip (12) at a 45 degree angle from vertical under the bolt. Ensure that the clip is bent toward the engine block.
Install the hardware that is shown in Illustration 31.
Illustration 32 | g02586476 |
(13) 3S-2093 Cable Strap (14) 4P-7581 Clip (15) 5M-2894 Hard Washer (16) 0T-0102 Bolt (17) 3S-2093 Cable Strap |
Install the hardware that is shown in Illustration 32.
Updating 289-2798 Exhaust Combustion Gp
Illustration 33 | g01371345 |
(1) 289-2798 Exhaust Combustion Gp |
Illustration 34 | g01371355 |
(2) 204-1611 Cable Strap (3) 285-6393 Clip (4) 290-1993 Cable Strap (5) 3S-2093 Cable Strap |
Install the hardware that is shown in Illustration 34.
Install the strap (5). Install the strap in the groove of the body of the connectors.
Illustration 35 | g01371360 |
(6) Boot and sensor (7) 290-1993 Cable Strap (8) 204-1611 Cable Strap (9) 285-6395 Clip (10) 290-1993 Cable Strap (11) 3S-2093 Cable Strap |
Orient the boot and the sensor (6) from 5 degrees to 10 degrees from horizontal.
Secure the excess wire from the sensor with strap (11) .
Install the remaining hardware that is shown in Illustration 35.
Updating 289-2822 Exhaust Combustion Gp
Illustration 36 | g01371377 |
(1) 289-2822 Exhaust Combustion Gp |
Illustration 37 | g01371379 |
(2) 204-1611 Cable Strap (3) 285-6395 Clip (4) 290-1993 Cable Strap (5) 3S-2093 Cable Strap |
Install the hardware that is shown in Illustration 37.
Install strap (5). Install the strap in the groove of the body of the connectors.
Illustration 38 | g01371382 |
(6) 204-1611 Cable Strap (7) 285-6395 Clip (8) 290-1993 Cable Strap (9) 3S-2093 Cable Strap |
Install strap (6) to the tube.
Secure excess wire from the sensor with strap (9) .
Install the remaining hardware that is shown in Illustration 38.
Illustration 39 | g02586619 |
(10) Sensor (11) Boot and sensor (12) 290-1993 Cable Strap (13) Strap |
Orient the sensor at the 6 o'clock position.
Orient the boot and the sensor (10) from 5 degrees to 10 degrees from horizontal.
Install strap (12) in order to strap the spark plug wire and the wire for the sensor together.
Install strap (13) to the existing clip.
Updating 289-2832 Exhaust Combustion Gp
Illustration 40 | g01371385 |
(1) 289-2832 Exhaust Combustion Gp |
Illustration 41 | g01371388 |
(2) 204-1611 Cable Strap (3) 3S-2093 Cable Strap (4) 3S-2093 Cable Strap |
Install strap (2) to the tube.
Install strap (3). Install the strap in the groove of the body of the connectors.
Secure the excess wire from the sensor with strap (4).
Illustration 42 | g01371390 |
(5) 277-1873 Clip (6) 9M-1974 Hard Washer (7) 5P-7970 Nut (8) 3S-2093 Cable Strap (9) 206-6875 Tube Cap |
Install the hardware that is shown in Illustration 42.
Illustration 43 | g02586856 |
(10) 290-1993 Cable Strap |
Install the hardware that is shown in Illustration 43.
Illustration 44 | g02586898 |
(11) 204-1611 Cable Strap (12) Strap |
Note: Route the wire outside of the CGI cooler line.
Connect strap (11) to the tube.
Install strap (12) to the existing clip.
Updating 289-2841 Exhaust Combustion Gp
Illustration 45 | g01371394 |
(1) 289-2841 Exhaust Combustion Gp |
Illustration 46 | g01371395 |
(2) 204-1611 Cable Strap (3) 3S-2093 Cable Strap (4) 285-6395 Clip (5) 290-1993 Cable Strap |
(2) Install three straps (2) to the tube.
(3) Install strap (3) to the existing clip.
Install clip (4) and strap (5) that is shown in Illustration 46.
Illustration 47 | g01371398 |
(6) 277-1873 Clip (7) 9M-1974 Hard Washer (8) 5P-7970 Nut (9) 3S-2093 Cable Strap (10) 206-6875 Tube Cap (11) 4P-7428 Clip (12) 5P-8245 Hard Washer (13) 8T-0293 Bolt (14) 3S-2093 Cable Strap (15) 4P-7428 Clip (16) 3S-2093 Cable Strap |
Install the hardware that is shown in Illustration 47.
Illustration 48 | g01371399 |
(17) 290-1993 Cable Strap (18) 285-6395 Clip (19) 9M-1974 Hard Washer (20) 6V-8212 Bolt (21) 290-1993 Cable Strap |
Install the hardware that is shown in Illustration 48.
Illustration 49 | g02587077 |
(22) 204-1611 Cable Strap (23) Strap |
(22) Install strap (22) to the tube.
(23) Install strap (23) to the existing clip.
Updating 289-2847 Exhaust Combustion Gp
Illustration 50 | g01371566 |
(1) 289-2847 Exhaust Combustion Gp |
Illustration 51 | g01371568 |
(2) 204-1611 Cable Strap (3) 3S-2093 Cable Straps (4) 3S-2093 Cable Strap |
(2) Install strap (2) to the tube.
(3) Install the two straps (3) on the existing clips. Install the straps in the groove of the body of the connector.
(4) Secure the excess wire from the sensor with strap (4).
Illustration 52 | g01371571 |
(5) 285-6395 Clip (6) 6V-5839 Washer (7) 6V-8189 Nut (8) 3S-2093 Cable Strap (9) 206-6875 Tube Cap |
Install the hardware that is shown in Illustration 52.
Illustration 53 | g02587016 |
(10) 3S-2093 Cable Strap (11) 285-6393 Clip (12) 290-1993 Cable Strap (13) 285-6393 Clip (14) 8T-4896 Hard Washer (15) 0L-1351 Bolt (16) 290-1993 Cable Strap (17) 285-6395 Clip (18) 290-1993 Cable Strap |
Install the hardware that is shown in Illustration 53.
Illustration 54 | g02587117 |
(19) 3S-2093 Cable Strap (20) 4P-7581 Clip (21) 8T-4896 Hard Washer (22) 0L-1351 Bolt (23) 3S-2093 Cable Strap |
Install clip (17) at a 45 degree angle from vertical under the bolt (18). Ensure that the clip is bent toward the engine block.
(19) Install strap (19) to the existing clip.
Install the remaining hardware that is shown in Illustration 54.
Updating 289-2852 Exhaust Combustion Gp
Illustration 55 | g01371595 |
(1) 289-2852 Exhaust Combustion Gp |
Illustration 56 | g01371598 |
(2) 204-1611 Cable Strap (3) 3S-2093 Cable Straps |
(2) Install strap (2) to the tube.
(3) Install the two straps (3). Install the straps in the groove of the body of the connectors.
Illustration 57 | g01371599 |
(4) 285-6395 Clip (5) 9M-1974 Hard Washer (6) 6V-8189 Nut (7) 3S-2093 Cable Strap (8) 206-6875 Tube Cap (9) 290-1993 Cable Strap |
Install the hardware that is shown in Illustration 57.
Illustration 58 | g02587876 |
(10) 285-6393 Clip (11) 290-1993 Cable Strap (12) 285-6395 Clip (13) 290-1993 Cable Strap |
Note: Install clip (17) at a 45 degree angle from vertical under the bolt. Ensure that the clip is bent toward the engine block.
(10) Install clip (10). Ensure that the clip is bent away from the block (11).
(12) Install clip (12). Install the clip at a 45 degree angle from vertical under the bolt (13).
Illustration 59 | g02587881 |
(14) 3S-2093 Cable Strap (15) 4P-7581 Clip (16) 8T-4896 Hard Washer (17) 0L-1351 Bolt (18) 3S-2093 Cable Strap |
(14) Install strap (14) to the existing clip.
(15) Install clip (15). Ensure that the clip is bent away from the block.
Install the remaining hardware that is shown in Illustration 59.
Updating 289-2857 Exhaust Combustion Gp
Illustration 60 | g01371604 |
(1) 289-2857 Exhaust Combustion Gp |
Illustration 61 | g01371612 |
(2) 204-1611 Cable Strap (3) 3S-2093 Cable Straps (4) 3S-2093 Cable Strap |
(2) Install strap (2) to the tube.
(3) Install the two straps (3). Install the straps in the grooves of the body of the connectors.
(4) Secure the excess wire from the sensor with strap (4).
Illustration 62 | g01371615 |
(5) 285-6395 Clip (6) 9M-1974 Hard Washer (7) 6V-8189 Nut (8) 3S-2093 Cable Strap (9) 206-6875 Tube Cap |
Install the hardware that is shown in Illustration 62.
Illustration 63 | g01371618 |
(10) 285-6393 Clip (11) 8T-4896 Hard Washer (12) 0L-1351 Bolt (13) 290-1993 Cable Strap (14) 204-1611 Cable Strap |
(14) Install strap (14) to the tube.
Install the remaining hardware that is shown in Illustration 63.
Illustration 64 | g02587940 |
(15) 285-6393 Clip (16) 290-1993 Cable Strap (17) 285-6395 Clip (18) 290-1993 Cable Strap |
(17) Install clip (17). Install the clip at a 45 degree angle from vertical under the bolt. Ensure that the clip is bent toward the block.
Install the remaining hardware that is shown in Illustration 63.
Illustration 65 | g02587959 |
(19) 3S-2093 Cable Strap (20) 4P-7581 Clip (21) 8T-4896 Hard Washer (22) 0L-1351 Bolt (23) 3S-2093 Cable Strap |
(19) Install the strap to the existing clip.
Install the remaining hardware that is shown in Illustration 65.
Updating 289-2873 Exhaust Combustion Gp
Illustration 66 | g01371625 |
(1) 289-2873 Exhaust Combustion Gp |
Illustration 67 | g01371626 |
(2) 204-1611 Cable Strap (3) 3S-2093 Cable Strap (4) 3S-2093 Cable Strap |
(2) Install the strap to the tube.
(3) Install the strap on the existing clips. Install the strap in the groove of the body of the connector.
(4) Secure the excess wire from the sensor with strap (4).
Illustration 68 | g01371627 |
(5) 290-1993 Cable Strap (6) 277-1873 Clip (7) 9M-1974 Hard Washer (8) 5P-7970 Nut (9) 3S-2093 Cable Strap (10) 206-6875 Tube Cap (11) 285-6393 Clip (12) 6V-5839 Washer (13) 6V-8212 Bolt (14) 290-1993 Cable Strap |
Install the hardware that is shown in Illustration 68.
Illustration 69 | g01371628 |
(15) Probe (16) 285-6395 Clip (17) 290-1993 Cable Strap |
(15) Orient the probe that is shown in Illustration 69.
Install the remaining hardware that is shown in Illustration 69.
Illustration 70 | g01371629 |
(18) Strap |
(18) Install the strap to the existing clip.
Updating 289-2878 Exhaust Combustion Gp
Illustration 71 | g01371630 |
(1) Exhaust Combustion Gp |
Illustration 72 | g01371631 |
(2) 204-1611 Cable Strap (3) 3S-2093 Cable Strap (4) 3S-2093 Cable Strap |
(2) Install the strap to the tube.
(3) Install the strap on the existing clip.
(4) Secure the excess wire from the sensor with strap (4).
Illustration 73 | g01371632 |
(5) 4P-7428 Clip (6) 5P-8245 Hard Washer (7) 8T-0293 Bolt (8) 3S-2093 Cable Strap (9) 4P-7428 Clip (10) 3S-2093 Cable Strap (11) 277-1873 Clip (12) 9M-1974 Hard Washer (13) 5P-7970 Nut (14) 3S-2093 Cable Strap (15) 206-6875 Tube Cap |
Install the hardware that is shown in Illustration 73.
Illustration 74 | g01371633 |
(16) 285-6395 Clip (17) 6V-5839 Washer (18) 6V-8212 Bolt (19) 290-1993 Cable Strap (20) 290-1993 Cable Strap |
Install the hardware that is shown in Illustration 74.
Illustration 75 | g02588057 |
(21) 204-1611 Cable Strap (22) Strap |
(21) Install the strap to the tube.
(22) Install the strap to the existing clip.
Updating 289-2890 Exhaust Combustion Gp
Illustration 76 | g01371635 |
(1) 289-2890 Exhaust Combustion Gp |
Illustration 77 | g01371637 |
(2) 204-1611 Cable Strap (3) 3S-2093 Cable Strap |
(2) Install the strap to the tube.
(3) Install the strap on the existing clip. Install the straps in the grooves of the connectors.
Illustration 78 | g01371639 |
(4) 285-6395 Clip (5) 9M-1974 Hard Washer (6) 6V-8189 Nut (7) 3S-2093 Cable Strap (8) 206-6875 Tube Cap (9) 290-1993 Cable Strap |
Install the hardware that is shown in Illustration 78.
Illustration 79 | g02588118 |
(10) 285-6393 Clip (11) 290-1993 Cable Strap (12) 285-6395 Clip (13) 290-1993 Cable Strap (14) 4P-5918 Clip (15) 290-1993 Cable Strap |
Note: Install clip (14) at a 45 degree angle from vertical under the bolt. Ensure that clip is bent toward the engine block.
Install the hardware that is shown in Illustration 79.
Illustration 80 | g02588124 |
(16) 3S-2093 Cable Strap (17) 4P-7581 Clip (18) 8T-4896 Hard Washer (19) 0L-1351 Bolt (20) 3S-2093 Cable Strap |
Install the hardware that is shown in Illustration 80.
Updating 289-2896 Exhaust Combustion Gp
Illustration 81 | g01371645 |
(1) 289-2896 Exhaust Combustion Gp |
Illustration 82 | g01371646 |
(2) 204-1611 Cable Strap (3) 3S-2093 Cable Straps |
(2) Install the strap to the tube.
(3) Install the three straps on the existing clips. Install the straps in the grooves of the bodies of the connectors.
Illustration 83 | g01371649 |
(4) 285-6395 Clip (5) 9M-1974 Hard Washer (6) 6V-8189 Nut (7) 3S-2093 Cable Strap (8) 206-6875 Tube Cap |
Install the hardware that is shown in Illustration 83.
Illustration 84 | g02588139 |
(9) 285-6393 Clip (10) 5M-2894 Hard Washer (11) 0L-1351 Bolt (12) 290-1993 Cable Strap (13) 285-6393 Clip (14) 290-1993 Cable Strap |
Install the hardware that is shown in Illustration 84.
Illustration 85 | g01371654 |
(15) 285-6393 Clip (16) 290-1993 Cable Strap (17) 285-6395 Clip (18) 290-1993 Cable Strap |
Install the hardware that is shown in Illustration 85.
Illustration 86 | g01371656 |
(19) 4P-7581 Clip (20) 5M-2894 Hard Washer (21) 0L-1351 Bolt (22) 3S-2093 Cable Strap (23) 4P-7581 Clip (24) 5M-2894 Hard Washer (25) 0L-1351 Bolt (26) 3S-2093 Cable Strap |
Install the hardware that is shown in Illustration 86.
Updating 293-4138 Exhaust Combustion Gp
Illustration 87 | g01371659 |
(1) 293-4138 Exhaust Combustion Gp |
Illustration 88 | g01371661 |
(2) 204-1611 Cable Strap (3) 3S-2093 Cable Strap (4) 3S-2093 Cable Strap (5) 285-6393 Clip (6) 290-1993 Cable Strap |
(2) Install the strap (2) to the tube.
(3) Install the strap (3). Install the strap in the groove of the body of the connector.
(4) Secure the excess length from the sensor with the strap (4).
Illustration 89 | g01371662 |
(7) 277-1873 Clip (8) 9M-1974 Hard Washer (9) 5P-7970 Nut (10) 3S-2093 Cable Strap (11) 206-6875 Tube Cap (12) 290-1993 Cable Strap |
Install the hardware that is shown in Illustration 89.
Illustration 90 | g01371663 |
(13) 204-1611 Cable Strap (14) Strap |
(13) Install the strap (13) to the tube.
(14) Install the strap (14) to the existing clip.
Updating 295-4608 Exhaust Combustion Gp
Illustration 91 | g01371664 |
(1) 295-4608 Exhaust Combustion Gp |
Illustration 92 | g01371665 |
(2) 204-1611 Cable Strap (3) 3S-2093 Cable Strap (4) 3S-2093 Cable Strap |
(2) Install the strap (2) to the tube.
(3) Install the strap (3). Install the strap in the groove of the body of the connector.
(4) Secure excess length from the sensor with the strap (4).
Illustration 93 | g02588336 |
(5) 3S-2093 Cable Strap (6) 290-1993 Cable Strap (7) 285-6395 Clip (8) 9M-1974 Hard Washer (9) 5P-7970 Nut (10) 3S-2093 Cable Strap (11) 206-6875 Tube Cap |
(5) Secure the excess wire from the sensor with the strap (5).
Install the remaining hardware that is shown in Illustration 93.
Illustration 94 | g02588440 |
(12) 277-1873 Clip (13) 3S-2093 Cable Strap (14) 132-5789 Clip (15) 9M-1974 Hard Washer (16) 5P-7970 Nut (17) 3S-2093 Cable Strap (18) 206-6875 Tube Cap |
Install the hardware that is shown in Illustration 94.
Illustration 95 | g02588449 |
(19) 290-1993 Cable Strap (20) 204-1611 Cable Strap (21) Strap |
(19) Install the strap (19).
(20) Install the strap (20) to the tube.
(21) Install the strap (21) to the existing clip.
Updating 300-6597 Exhaust Combustion Gp
Illustration 96 | g01371670 |
(1) 300-6597 Exhaust Combustion Gp |
Illustration 97 | g01371671 |
(2) 3S-2093 Cable Straps (3) 204-1611 Cable Strap |
(2) Install the straps (2). Install the straps in the groove of the body of the connector.
(3) Install the strap (3) to the tube.
Illustration 98 | g01371674 |
(4) 290-1993 Cable Straps |
(4) Install the straps that are shown in Illustration 98.
Illustration 99 | g01371675 |
(5) 204-1611 Cable Strap (6) 285-6395 Clip (7) 290-1993 Cable Strap (8) 285-6393 Clip (9) 290-1993 Cable Strap |
(5) Install the strap (5) to the tube.
Install the remaining hardware that is shown in Illustration 99.
Illustration 100 | g01371676 |
(10) 290-1993 Cable Strap (11) 4P-7581 Clip (12) 9M-1974 Hard Washer (13) 6V-5217 Bolt (14) 3S-2093 Cable Strap |
Install the hardware that is shown in Illustration 100.