Gear Group (Front)
Show/hide table
图 1 | g03344812 |
Show/hide table
图 2 | g03344855 |
Show/hide table
366-0232 前齿轮总成的技术规格 | |||
项目 | 数量 | 零件 | 技术规格说明 |
1 | 6 | 031-3185 螺栓 | 按照图 2 中所示的数字顺序 1、4、2、5、3、6、1、4,将螺栓拧紧至扭矩为 |
Show/hide table
项目 | 数量 | 零件 | 技术规格说明 |
B | - | - | 拧紧枢轴螺栓前,用仪表对凸轮轴齿轮和齿轮组件的中心之间的距离 (B) 进行设置,以便获得 |
C | 1 | 6V-3677 定位销 | 新定位销的延伸量为 |
2 | 1 | 361-8240 凸轮轴齿轮 | 凸轮轴齿轮后端面上的 103-0126 定位销的延伸量为 |
3 | 8 | 0S-1571 螺栓 | 拧紧至扭矩为 |
4 | 1 | 102-5861 止推片 | 厚度为 |
5 | 1 | 117-8801 O 形密封圈 | 在装配前,用按 50/50 比例混合的 8T-2998 润滑剂和清洁的发动机机油稍微润滑孔。 |
6 | 1 | 417-4617 惰轮组件 | 安装后, 417-4618 衬套中用于安装枢轴的孔径为 衬套的安装深度为 |
7 | 1 | 151-5966 枢轴组件 | 直径为 6I-3623 定位销的延伸长度为 |
8 | 1 | 417-4615 惰轮组件 | 安装后, 417-4616 衬套中的孔径为 衬套的安装深度为 |
9 | 1 | 158-3416 枢轴 | 直径为 |
Show/hide table
图 3 | g03344857 |
剖面 D-D |
Show/hide table
图 4 | g03344813 |
Show/hide table
项目 | 数量 | 零件 | 技术规格说明 |
10 | 1 | 361-8233 齿轮组组件 | 安装后, 128-2661 衬套中的孔径为 安装深度为 |
11 | 1 | 197-4971 枢轴 | 新枢轴的直径为 |
12 | 5 | 2J-3118 锁紧螺栓 | 按照图 4 中所示的数字顺序 1、3、4、5、2、1、3、4、5、1,将螺栓拧紧至扭矩为 |
13 | 1 | 112-9217 止推片 | 将止推片的油槽朝向齿轮组件的端面安装。
厚度为 |
14 | 1 | 0S-1571 螺栓 | 拧紧至扭矩为 |
Show/hide table
图 5 | g03349381 |
Show/hide table
项目 | 数量 | 零件 | 技术规格说明 |
15 | 2 | 6I-3624 止推片 | 将止推片的油槽朝向齿轮组件的端面安装。
厚度为 |
16 | 2 | 5P-4142 锁紧螺栓 | 拧紧至扭矩为 |
17 | 10 | 9S-8752 全高螺母 | 当松开任何螺母以进行维修时,参考以下步骤: 1. 拆下螺母。 2. 用钢丝刷清洁螺母。 3. 在装配前,将蓝色 Loctite 242 涂覆到螺纹上。 4. 将螺母拧紧至扭矩为 |
18 | 10 | 126-1756 锁紧螺栓 | 当松开任何螺栓以进行维修时,参考以下步骤: 1. 拆下螺栓。 2. 用钢丝刷清洁螺栓。 3. 在装配前,将蓝色 Loctite 242 涂覆到螺纹上。 允许使用预先涂覆了螺纹锁固胶的新螺栓。 4. 拧紧螺栓至扭矩为 |
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Water Pump
903C Compact Wheel Loader Work Tool Coupler Operation
Replacement Procedure of the Electronic Filter Control for the Service Hour Meter on Certain Track-Type Tractors{1623, 7478} Replacement Procedure of the Electronic Filter Control for the Service Hour Meter on Certain Track-Type Tractors{1623, 7478}
2013/02/22 An Improved Clevis Pin and Cotter Pin for the Transmission Control Group Are Now Used on Certain D6R and D7R Track-Type Tractors {4122}
C7.1 Engines for Caterpillar Built Machines Fuel Injection Nozzles
2013/03/15 New Cylinder Stop Is Now Installed on Certain D3K2, D4K2 and D5K2 Track-Type Tractors with Both Power Pitch Cylinder And Blade Control System {7220}
C7.1 Engines for Caterpillar Built Machines Valve Mechanism Cover
901C, 901C2, 902C, 902C2, 903C and 903C2 Compact Wheel Loaders Control Valve (Speed Sensing)
C7.1 Industrial Engine Sensors and Electrical Components
336F MHPU Mobile Hydraulic Power Unit Machine System Specifications Hydraulic Oil Cooler Lines Group
C4.4 Industrial Engine Monitoring System
C4.4 Industrial Engine Gauges and Indicators
2013/03/21 A New Procedure for Checking Steering Cylinder and Frame Stop Dimensions is Now Available {4303, 4304, 4330, 7050, 7188}
988H Wheel Loader, 834H Wheel Dozer and, 836H Landfill CompactorTransmission Pump Shaft and Gear Failures {3066, 5073} 988H Wheel Loader, 834H Wheel Dozer and, 836H Landfill CompactorTransmission Pump Shaft and Gear Failures {3066, 5073}
2013/04/15 Improved HMU Steering Lines are Now Available for Certain 950H and 962H Wheel Loaders {4304, 4312, 5057}
335F Excavator Additional Messages
335F Excavator Service Interval Chart
D10T2 Track-Type Tractor Symptom Troubleshooting
C7.1 Engines for Caterpillar Built Machines Fuel Injection Lines
C7.1 Engines for Caterpillar Built Machines Engine Design
D10T2 Track-Type Tractor Emerging Symptom Information
D10T2 Track-Type Tractor Implement System
D10T2 Track-Type Tractor Machine Preparation for Troubleshooting
D10T2 Track-Type Tractor Wiring Harness (Open Circuit) - Test