Bulldozer Control Valve
Show/hide table
图 1 | g02710278 |
Show/hide table
244-5440 控制阀总成 的技术规格     | |||
项目     | 数量     | 零件     | 技术规格说明     |
1     | 2     | 8J-8621 弹簧     | 在试验力下的长度为 40.6 mm (1.60 in)。 试验力为 45.0 ± 3.6 N (10.1 ± 0.8 lb)。 试验后的自由长度为 46.0 mm (1.81 in)。     |
2     | 1     | 8M-1679 弹簧     | 在试验力下的长度为 18.5 mm (0.72 in)。 试验力为 27.0 ± 2.0 N (6.1 ± 0.4 lb)。 试验后的自由长度为 133.9 mm (5.27 in)。     |
3     | 1     | 178-2313 弹簧     | 在试验力下的长度为 66.5 mm (2.62 in)。 试验力为 774 ± 62 N (174 ± 14 lb)。 试验后的自由长度为 70.0 mm (2.76 in)。     |
4     | 1     | 178-2314 弹簧     | 在试验力下的长度为 57.4 mm (2.26 in)。 试验力为 284 ± 40 N (64 ± 9 lb)。 试验后的自由长度为 62.17 mm (2.448 in)。     |
5     | 3     | 180-7154 垫片     | 根据需要,使用厚度为 1.00 mm (0.039 in) 的垫片。 垫片必须接触到 178-2314 弹簧 (4) 的端部。     |
6     | 2     | 5N-9016 垫片     | 根据需要,使用厚度为 0.25 mm (0.010 in) 的垫片来控制压力。     |
7     | 2     | 9F-2167 排气螺钉     | 拧紧至扭矩为 6.4 ± 1.0 N·m (56.6 ± 8.9 lb in)。     |
Show/hide table
图 2 | g02710279 |
Show/hide table
8     | 2     | 3G-8165 螺母     | 拧紧至扭矩为 20 ± 6 N·m (177 ± 53 lb in)。     |
9     | 2     | 3G-8164 螺母     | 拧紧扭矩至 35 ± 6 N·m (26 ± 4 lb ft)。     |
10     | 1     | 152-7041 垫片     | 根据需要,使用厚度为 0.250 ± 0.015 mm (0.0098 ± 0.0006 in) 的垫片来控制压力。     |
11     | 2     | 9T-5734 隔套     | 根据需要,使用厚度为 1.20 mm (0.047 in) 的隔套。 隔套必须接触到 340-0552 弹簧 (14) 的端部。     |
12     | 1     | 008-2103 O 形密封圈     | 利用所密封的润滑剂轻轻润滑孔。     |
13     | 2     | 6J-3134 O 形密封圈     | 利用所密封的润滑剂轻轻润滑孔。     |
14     | 1     | 340-0552 弹簧     | 在试验力下的长度为 33.3 mm (1.31 in)。 试验力为 245.7 ± 20.0 N (55.2 ± 4.5 lb)。 试验后的自由长度为 36.17 mm (1.424 in)。     |
15     | 4     | 152-5559 垫片     | 根据需要,使用厚度为 0.95 ± 0.05 mm (0.037 ± 0.002 in) 的垫片来控制压力。     |
16     | 1     | 9J-5499 弹簧     | 在试验力下的长度为 46.02 mm (1.812 in)。 试验力为 88.9 ± 4.4 N (20.0 ± 1.0 lb)。 试验后的自由长度为 68.1 mm (2.68 in)。     |
17     | 7     | 152-7041 垫片     | 根据需要,使用厚度为 0.250 ± 0.015 mm (0.0098 ± 0.0006 in) 的垫片来控制压力。     |
18     | 2     | 9T-5734 隔套     | 根据需要,使用厚度为 1.20 mm (0.047 in) 的隔套。 隔套必须接触到 2J-6089 弹簧 (18) 的端部。     |
19     | 1     | 2J-6089 弹簧     | 在试验力下的长度为 36.25 mm (1.427 in)。 试验力为 278 ± 14 N (62 ± 3 lb)。 试验后的自由长度为 44.12 ± 0.51 mm (1.737 ± 0.020 in)。     |
20     | 4     | 152-5559 垫片     | 根据需要,使用厚度为 0.95 ± 0.05 mm (0.037 ± 0.002 in) 的垫片来控制压力。     |
21     | 1     | 2N-7029 弹簧     | 在试验力下的长度为 31.0 mm (1.22 in)。 试验力为 17.8 N (4.0 lb)。 试验后的自由长度为 50.0 mm (1.97 in)。     |
22     | 1     | 9J-8752 弹簧     | 在试验力下的长度为 81.0 mm (3.19 in)。 试验力为 337 ± 17 N (76 ± 4 lb)。 试验后的自由长度为 116.8 mm (4.60 in)。     |
23     | 1     | 3B-4730 弹簧     | 在试验力下的长度为 53.98 mm (2.125 in)。 试验力为 35.6 ± 42.3 N (8.0 ± 9.5 lb)。 试验后的自由长度为 82.6 mm (3.25 in)。     |
24     | 1     | 178-2312 弹簧     | 在试验力下的长度为 96.4 mm (3.80 in)。 试验力为 782 ± 55 N (176 ± 12 lb)。 试验后的自由长度为 102.0 mm (4.02 in)。     |
25     | 1     | 178-2311 弹簧     | 在试验力下的长度为 82.5 mm (3.25 in)。 试验力为 398 ± 28 N (89 ± 6 lb)。 试验后的自由长度为 89.17 mm (3.511 in)。     |
26     | 2     | 7F-1585 弹簧     | 在试验力下的长度为 37.3 mm (1.47 in)。 试验力为 16.0 N (3.6 lb)。 试验后的自由长度为 82.6 mm (3.25 in)。     |
27     | 2     | 5N-9016 垫片     | 根据需要,使用厚度为 0.25 mm (0.010 in) 的垫片来控制压力。     |
28     | 3     | 180-7154 垫片     | 根据需要,使用厚度为 1.00 mm (0.039 in) 的垫片。 垫片必须接触到 178-2312 弹簧 (22) 的端部。     |
Caterpillar Information System:
C6.6 Industrial Engine Diesel Particulate Filter - Remove
C6.6 Industrial Engine Diesel Particulate Filter - Install
Installation Of Differential Steering Control Update On The D6T, D7E, And D8T Track-Type Tractors{5063, 5705} Installation Of Differential Steering Control Update On The D6T, D7E, And D8T Track-Type Tractors{5063, 5705}
C13, C15, and C18 Tier 4 Final Engines Exhaust Lines (DPF Inlet)
D11T Track-Type Tractor Hydraulic System Bypass Valve (Hydraulic Oil Cooler)
621G, 623G, 627G, 631G, 637G, and 657G Wheel Tractor-Scrapers Power Train Electronic Control System MID 027 - CID 0590 - FMI 02
953D Welding Tractor Safety Messages
Instructions to Register the Retrofit and Submit Service Reporting {1000, 3000, 7000, 7570} Instructions to Register the Retrofit and Submit Service Reporting {1000, 3000, 7000, 7570}
D6T Track-Type Tractor Engine and Machine Warm-Up
2010/11/24 Improvement To The Hydraulic Tank Implement Return Tube Are Now Used On The D8T {5056}
D11T Track-Type Tractor Hydraulic System Dual Tilt Control Valve
C13 Engines for Caterpillar Built Machines Diesel Particulate Filter
980K Wheel Loader Electrohydraulic System Work Tool Control
953D Welding Tractor Specifications
Update to the Fuel Level Sender Assembly for the IT38H Integrated Toolcarrier and 938H Wheel Loaders{1273, 7422} Update to the Fuel Level Sender Assembly for the IT38H Integrated Toolcarrier and 938H Wheel Loaders{1273, 7422}
2010/10/29 Additional Harness Protection Has Been Added {1408, 7324}
2010/11/01 A Procedure Is Now Available to Replace Engine Starting Motor Cable and Eliminate Main Fuse {1408}
D11T Track-Type Tractor Hydraulic System Fan Drive Pump
C32 LRC Engine for Track-Type Tractors Speed Control (PWM) - Test
2011/02/28 New Power Train Software Group Is Now Used on Certain Series G Wheel Tractor-Scrapers {7610, 7620}
D6T Track-Type Tractor Engine including Specifications Piston Motor (Hydraulic Fan) and Fan
994H Wheel Loader Machine Systems Rollover Protective Structure (ROPS)
994H Wheel Loader Machine Systems Platform Mounting
994H Wheel Loader Machine Systems Window Wiper and Wiper Motor (Front, Rear)