Exhaust Manifold
Show/hide table
| |
| Illustration 1 | g02558316 |
Show/hide table
| |
| Illustration 2 | g02559876 |
|
Tightening sequence | |
Show/hide table
| Specification for 343-0589 Exhaust Manifold Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 12 | 9X-6620 Locknut | Before assembly, apply 4C-5599 Anti-Seize Compound to the threads.
Torque to Refer to Illustration 2 for the locknut tightening procedure. |
| 2 | 12 | 116-3715 Taperlock Stud | Torque tool speed should not exceed 100 rpm.
Torque to |
| 3 | 1 | 324-9290 Bellows As | Assemble the bellows assembly with the “Flow Arrow” toward the NOx Reduction System (NRS) cooler.
The total maximum misalignment of the bellows assembly allowed between the NRS cooler and the exhaust manifold elbow is |
| 4 | 2 | 9N-5085 Clamp | Torque to |
| 5 | 1 | 231-9030 Exhaust Manifold | Before assembly, apply thin coat of 2P-2333 High Temperature Sealer to the outside diameter of the male end of the exhaust manifold.
Remove the excess sealer from the assembled joints. |
| 6 | 6 | 283-2238 Gasket | Install the gasket with tab down as shown in Illustration 1. |
| 7 | 1 | 375-8486 Exhaust Manifold | Before assembly, apply thin coat of 2P-2333 High Temperature Sealer to the inside diameter of the female end of the exhaust manifold.
Remove the excess sealer from the assembled joints. |
| 8 | 4 | 376-3408 Taperlock Stud | Torque tool speed should not exceed 100 rpm.
Torque to |
| 9 | 1 | 350-4503 Exhaust Manifold | Before assembly, apply thin coat of 2P-2333 High Temperature Sealer to the outside diameter of the male end of the exhaust manifold.
Remove the excess sealer from the assembled joints. |
| B | - | - | Angle of the V-band clamp is 45 ± 5 degrees. |
Caterpillar Information System:
854K Wheel Dozer and 992K Wheel Loader Electric Starting Motor - Remove and Install - Engine in Chassis
D8T and D9T Track-Type Tractors MID 113 - CID 2596 - FMI 05
2010/06/21 Reworking of the Axle Hub Bolts on Certain Compact Wheel Loaders {3278, 4050, 4084}
980K Wheel Loader Engine Compartment - Clean
D11T Track-Type Tractor Hydraulic System Reversing Hydraulic Fan System (Optional)
D11T Track-Type Tractor Hydraulic System Fan Drive Motor
D11T Track-Type Tractor Hydraulic System Fan Drive Pump - Fan Pump Section and Control Valve
D11T Track-Type Tractor Hydraulic System Fan Drive System
D11T Track-Type Tractor Hydraulic System Pin Puller Hydraulic System
D11T Track-Type Tractor Hydraulic System Dual Tilt Control Valve - Equipped Without the Quick Dump Valve
980K Wheel Loader Windows - Clean
D11T Track-Type Tractor Hydraulic System Quick-Drop Valve
2010/06/17 New VIMS Software Is Now Available For Certain CAT Product {7601, 7620}
D8T and D9T Track-Type Tractors MID 113 - CID 2596 - FMI 06
980K Wheel Loader Electrohydraulic System Ride Control Valve
D11T Track-Type Tractor Hydraulic System Operational Tests
D11T Track-Type Tractor Hydraulic System Relief Valve - Test and Adjust
D11T Track-Type Tractor Hydraulic System Pilot System Pressure - Test and Adjust
D8T and D9T Track-Type Tractors MID 113 - CID 2596 - FMI 13
D11T Track-Type Tractor Hydraulic System Accumulator - Test and Charge
D11T Track-Type Tractor Hydraulic System Hydraulic Fan Drive System - Test and Adjust
D8T and D9T Track-Type Tractors MID 113 - CID 3642 - FMI 02
854K Wheel Dozer and 992K Wheel Loader Fuel Cooler - Remove and Install
966K and 972K Wheel Loaders Transmission Oil - Change