Engine Oil Filter Base and Oil Cooler - Remove
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 185-3630 | Strap Wrench As | 1 |
Start By:
- Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
- Drain the engine oil into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change".
- Drain the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Show/hide table
Illustration 1 g01258099 - Remove nuts (1). Remove bracket (2) and the hose assembly. Use Tooling (A) and remove oil filter (3).
Show/hide table
Illustration 2 g01258101 - Remove bolts (4). Remove engine oil filter base (5) and the gasket.
Show/hide table
Illustration 3 g01258137 - Remove oil cooler (6) and the gasket. Remove O-ring seals (7).
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Caterpillar Information System:
2006/04/01 A Reman Short Block has Been Released {1201}
C7 PETROLEUM Petroleum Engine Flywheel Adapter - Remove and Install
C7 PETROLEUM Petroleum Engine Flywheel Housing - Remove and Install
3500B and 3500C Locomotive Engines Analog Sensor (Active)
C7 On-Highway Engine Turbocharger - Install
C7 PETROLEUM Petroleum Engine Flywheel - Remove and Install
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Power Sources
G3500 A3 Engines Cooling System
C7 On-Highway Engine Exhaust Manifold - Remove and Install
G3500 A3 Engines Electronic Service Tools
C7 PETROLEUM Petroleum Engine Water Temperature Regulator Housing - Remove and Install
2006/04/03 Replace the Fuel Injector Hold-Down Bolt When You Service the Electronic Unit Injectors on Engines, Including Remanufactured Engines with Serial Number Prefix 3LZ, AKB, ALS or R1D {1251, 1254}
C9.3 Tier 4 Final Engines Coolant Temperature Sensor
2006/05/22 Improved Rectifier for Heat Sink Assembly {4465, 4472}
3500B and 3500C Locomotive Engines CAN Data Link
C175 Generator Sets General Maintenance Information
C7 PETROLEUM Petroleum Engine Vibration Damper and Pulley - Remove and Install
C7 On-Highway Engine Engine Oil Filter Base and Oil Cooler - Install
Inability to Flash ECM Software on Certain Generator Sets{7620} Inability to Flash ECM Software on Certain Generator Sets{7620}
C9 Industrial Engines Jacket Water Heater
C9 Industrial Engines Jacket Water Heater
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Gear Pump (Transmission)
C7 On-Highway Engine Engine Oil Filter Base and Oil Cooler - Disassemble
3500B and 3500C Locomotive Engines Cat Data Link