Flywheel Adapter - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | 导向螺柱 M12 - 1.75 乘以 8 in     |
1     |
开始:
- 拆下电起动马达。 请参阅拆解和组装, "电起动马达 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下螺栓 (1) 。 将工具 (A) 插入曲轴中。 将螺栓 (1) 和板 (2) 从适配器总成 (3) 上拆下。
Show/hide table
图 1 | g01257939 |
- 将适配器总成 (3) 从飞轮壳上拆下。
- 必要时,利用手锤和冲头将轮毂 (5) 从适配器总成 (3) 上拆下。
注: 适配器总成 (3) 的重量大约为 10 kg (21 lb)。
Show/hide table
图 2 | g01257948 |
- 利用手锤和冲头将齿圈 (4) 从适配器总成 (3) 上拆下。
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | 导向螺柱 M12 - 1.75 乘以 8 in     |
1     |
B     | 9S-3263     | 螺纹锁固胶     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将齿圈 (4) 加热到 316 °C (600 °F) 的最高温度。 将齿圈 (4) 安装到适配器总成 (3) 上。
Show/hide table
图 3 | g01257948 |
注: 安装齿圈 (4) 的时候必须让轮齿斜面一侧朝上。 适配器总成 (3) 安装后,轮齿斜面一侧应面向起动马达。
- 将轮毂 (5) 装入适配器总成 (3) 。
- 将工具 (A) 安装在曲轴中。
注: 适配器总成 (3) 的重量大约为 10 kg (21 lb)。
Show/hide table
图 4 | g01257939 |
- 将适配器总成 (3) 定位到曲轴上。
- 将工具 (B) 涂抹在螺栓 (1) 的螺纹上。
- 安装板 (2) 和螺栓 (1) 。 拆下工具 (A) 。 安装螺栓 (1) 来代替工具 (A) 。
- 拧紧螺栓 (1) 至扭矩为 120 ± 20 N·m (89 ± 15 lb ft)。
End By: 安装电起动马达。 请参阅 拆解和组装, "电起动马达 - 拆卸和安装"。
Caterpillar Information System:
C7 PETROLEUM Petroleum Engine Flywheel Housing - Remove and Install
3500B and 3500C Locomotive Engines Analog Sensor (Active)
C7 On-Highway Engine Turbocharger - Install
C7 PETROLEUM Petroleum Engine Flywheel - Remove and Install
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Power Sources
G3500 A3 Engines Cooling System
C7 On-Highway Engine Exhaust Manifold - Remove and Install
G3500 A3 Engines Electronic Service Tools
C7 PETROLEUM Petroleum Engine Water Temperature Regulator Housing - Remove and Install
2006/04/03 Replace the Fuel Injector Hold-Down Bolt When You Service the Electronic Unit Injectors on Engines, Including Remanufactured Engines with Serial Number Prefix 3LZ, AKB, ALS or R1D {1251, 1254}
C7 PETROLEUM Petroleum Engine Water Pump - Install
2006/04/01 Replace the Fuel Injector Hold-Down Bolt When You Service the Electronic Unit Injectors on Engines, Including Remanufactured Engines with Serial Number Prefix 3LZ, AKB, ALS or R1D {1251, 1254}
2006/04/01 A Reman Short Block has Been Released {1201}
C7 On-Highway Engine Engine Oil Filter Base and Oil Cooler - Remove
C9.3 Tier 4 Final Engines Coolant Temperature Sensor
2006/05/22 Improved Rectifier for Heat Sink Assembly {4465, 4472}
3500B and 3500C Locomotive Engines CAN Data Link
C175 Generator Sets General Maintenance Information
C7 PETROLEUM Petroleum Engine Vibration Damper and Pulley - Remove and Install
C7 On-Highway Engine Engine Oil Filter Base and Oil Cooler - Install
Inability to Flash ECM Software on Certain Generator Sets{7620} Inability to Flash ECM Software on Certain Generator Sets{7620}
C9 Industrial Engines Jacket Water Heater
C9 Industrial Engines Jacket Water Heater
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Gear Pump (Transmission)