Vibration Damper and Pulley - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | -     | Guide Bolt 5/8 - 18 NF by 7 inch     |
1     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove one of bolt (1). Install Tooling (A) .
Show/hide table
Illustration 1 | g01255615 |
- Remove remaining bolts (1). Remove plate (2). Remove pulley (3). Remove vibration damper (4) from adapter (5) .
Show/hide table
Illustration 2 | g01255608 |
- Remove adapter (5) from the crankshaft.
- Remove Tooling (A) from the crankshaft.
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | -     | Guide Bolt 5/8 - 18 NF by 7 inch     |
1     |
B     | 4C-5593     | Anti-Seize Compound     | -     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Thoroughly inspect the viscous damper for signs of leakage or for signs of a dented (damaged) case. Either of these conditions can cause the weight to make contact with the case. This can affect the viscous damper's operation. |
- Install Tooling (A) in the crankshaft.
Show/hide table
Illustration 3 | g01255608 |
- Install adapter (5) and vibration damper (4) on Tooling (A).
- Install pulley (3) on Tooling (A) .
- Install plate (2) on Tooling (A) .
- Apply Tooling (B) to bolts (1). Install bolts (1). Remove Tooling (A) and install the remaining bolt (1) .
Caterpillar Information System:
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Power Train Electronic Control System MID 027 - CID 0702 - FMI 02
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Power Train Electronic Control System MID 027 - CID 0668 - FMI 09
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Power Train Electronic Control System MID 027 - CID 0177 - FMI 01
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Power Train Electronic Control System MID 027 - CID 0177 - FMI 00
Turbocharger Surge on G3500 Generator Sets and G3500 Generator Set Engines that are Equipped with Dual Turbochargers{1052, 1057, 1071} Turbocharger Surge on G3500 Generator Sets and G3500 Generator Set Engines that are Equipped with Dual Turbochargers{1052, 1057, 1071}
2006/04/03 A New Grease is Used {0645}
C15 On-Highway Engine Belt Tensioner - Remove and Install
C15 On-Highway Engine Engine Oil Pressure Sensor - Remove and Install
C15 On-Highway Engine Coolant Temperature Sensor - Remove and Install
3126B Marine Engine Safety Messages
3116 and 3126 Marine Engines Declaration of Conformity
C-15, C-16, and C-18 Truck Engines Alternator and Regulator
C15 On-Highway Engine Crankshaft Front Seal - Remove
C15 On-Highway Engine Crankshaft Front Seal - Install
G3500 A3 Engines Cover Group (Front Housing)
G3500 Engines Before Starting Engine
C7 On-highway Engine Fan Drive Mounting Group
G3508, G3512 and G3516 Engines Vibration Damper - Remove and Install
C15 On-Highway Engine Engine Oil Filter Base - Disassemble
C7 PETROLEUM Petroleum Engine Fuel Transfer Pump - Remove
C15 On-Highway Engine Engine Oil Filter Base - Assemble
G3516B and G3520B Generator Set Engines Flywheel - Remove and Install
C7 On-highway Engine Jacket Water Heater
G3500 Engines Cold Weather Starting