Vibration Damper - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7575     | Link Bracket     | 2     |
B     | -     | Guide Bolt 1 - 14 NF by 11 inch     |
2     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove two bolts (3) .
Show/hide table
Illustration 1 | g01255751 |
- Attach Tooling (A) and a suitable lifting device to vibration damper (1) and adapter (4). The weight of vibration damper (1) and adapter (4) is approximately 90 kg (200 lb).
- Remove two bolts (2) and install Tooling (B) .
- Remove remaining bolts (2) and slide vibration damper (1) and adapter (4) off Tooling (B) .
- If necessary, remove remaining bolts (3) and vibration damper (1) from adapter (4). The weight of vibration damper (1) is approximately 51 kg (112 lb).
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7575     | Link Bracket     | 2     |
B     | -     | Guide Bolt 1 - 14 NF by 11 inch     |
2     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Attach Tooling (A) and a suitable lifting device to vibration damper (1). The weight of vibration damper (1) is approximately 51 kg (112 lb).
Show/hide table
Illustration 2 | g01255751 |
- If vibration damper (1) was removed from adapter (4), install vibration damper (1) on adapter (4) with bolts (3) .
- Install Tooling (B) in the crankshaft.
- Position vibration damper (1) and adapter (4) on Tooling (B). The weight of vibration damper (1) and adapter (4) is approximately 90 kg (200 lb). Slide vibration damper (1) and adapter (4) against the crankshaft.
- Install bolts (2). Remove Tooling (B) and install remaining bolts (2). Tighten bolts (2) to a torque of 1150 ± 150 N·m (850 ± 110 lb ft).
- Remove Tooling (A) and install remaining bolts (3) .
Note: Refer to Specifications, "Vibration Damper" for more information.
Caterpillar Information System:
C7 On-highway Engine Fan Drive Mounting Group
G3500 Engines Before Starting Engine
G3500 A3 Engines Cover Group (Front Housing)
C15 On-Highway Engine Crankshaft Front Seal - Install
C15 On-Highway Engine Crankshaft Front Seal - Remove
C15 On-Highway Engine Vibration Damper and Pulley - Remove and Install
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Power Train Electronic Control System MID 027 - CID 0702 - FMI 02
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Power Train Electronic Control System MID 027 - CID 0668 - FMI 09
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Power Train Electronic Control System MID 027 - CID 0177 - FMI 01
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Power Train Electronic Control System MID 027 - CID 0177 - FMI 00
Turbocharger Surge on G3500 Generator Sets and G3500 Generator Set Engines that are Equipped with Dual Turbochargers{1052, 1057, 1071} Turbocharger Surge on G3500 Generator Sets and G3500 Generator Set Engines that are Equipped with Dual Turbochargers{1052, 1057, 1071}
2006/04/03 A New Grease is Used {0645}
C15 On-Highway Engine Engine Oil Filter Base - Disassemble
C7 PETROLEUM Petroleum Engine Fuel Transfer Pump - Remove
C15 On-Highway Engine Engine Oil Filter Base - Assemble
G3516B and G3520B Generator Set Engines Flywheel - Remove and Install
C7 On-highway Engine Jacket Water Heater
G3500 Engines Cold Weather Starting
G3500 Engines Starting the Engine
C15 Industrial Engine Cooling Fan Circuit and A/C High Pressure Switch Circuit - Test
C13, C15, and C18 Tier 4 Final Engines Flywheel
C3.3 and C4.4 Generator Sets Flywheel Housing - Remove and Install
3500B and 3500C Locomotive Engines Electrical Connectors and Functions
C3.3 and C4.4 Generator Sets Engine Lifting Group - Remove and Install