Improved Cab Insulation Is Now Available {7301}
- Track-Type Tractor:
- D6N (S/N: DJA1-UP; DJY1-UP)
Description of Change: Improved cab insulation is now available for the D6N Track-Type Tractor. The improved insulation will help to reduce engine noise. The improved insulation also helps to improve the cab pressurization in order to prevent dust from entering into the cab.
Adaptable To: The improved cab insulation is effective with the D6N (S/N: DJA822-UP; DJY1205-UP). The following rework procedure is adaptable to the D6N (S/N: DJA1-821; DJY1-1204).
Rework Procedure
Required Parts
Show/hide table
Required Parts     | |||
---|---|---|---|
Item     | Part Number     | Description     | Qty     |
1     | 201-4066     | Seal     | 395 mm (15.6 inch)     |
2     | 5P-5639     | Seal     | 420 mm (16.5 inch)     |
3     | 321-3105     | Insulation     | 1     |
Installation Procedure
- Disassemble the 249-8089 Rear Cover at the rear of the seat.
- Disassemble the right hand 240-0488 Armrest .
- Disassemble right hand plastic console (4) .
Show/hide table
Illustration 1 | g01519346 |
- Add seal (1) around the joystick for the bulldozer blade. Seal (1) must begin at grommet (5) for the electrical wire.
Show/hide table
Illustration 2 | g01519347 |
- Disassemble control plate (6) .
Show/hide table
Illustration 3 | g01519349 |
- Add 300 mm (11.8 inch) of seal (2) to control plate (6). Refer to Illustration 3 for the location of seal (2) .
- Assemble control plate (6) .
- If the machine has a rear attachment control, add 60 mm (2.4 inch) of seal (2) to both sides of the ripper/winch control. Refer to Illustration 4 for the correct location of seal (2) .
Show/hide table
Illustration 4 | g01519350 |
- Assemble the right hand plastic console.
- Assemble the right hand 240-0488 Armrest .
- Assemble the 249-8089 Rear Cover at the rear of the seat.
- Disassemble firewall panel (7) .
Show/hide table
Illustration 5 | g01519351 |
- Remove the air filter.
- Remove the protection plate in order to access the heater compartment.
- Add insulation (3) under the heater coil.
Show/hide table
Illustration 6 | g01519352 |
- Assemble the protective plate.
- Assemble the air filter.
- Assemble the firewall panel.
Caterpillar Information System:
973K Track-Type Loader Machine Systems Cab Tilt Cylinder - Remove and Install
Procedure to Install Automotive Fuses{1408, 1417, 7278} Procedure to Install Automotive Fuses{1408, 1417, 7278}
C4.4 and C6.6 Engines for Caterpillar Built Machines Throttle Switch Circuit - Test
D7E Track-Type Tractor Power Train Gear Pump (Power Train) - Assemble
D7E Track-Type Tractor Power Train Gear Pump (Power Train) - Disassemble
973K Track-Type Loader Power Train Track - Connect
973K Track-Type Loader Power Train Track - Separate
613G Wheel Tractor-Scraper Hydraulic System Ejector Cylinder
2008/05/05 New AccuGrade® Firmware is Now Available {7220, 7620}
D7E Track-Type Tractor Cooling Systems Hydraulic Oil Cooling System
904H Compact Wheel Loader Hydraulic and Steering System Worksheets
854K Wheel Dozer Machine Systems Front Frame and Rear Frame - Connect
D6N Track-Type Tractor Machine Systems Air Cleaner
D6N Track-Type Tractor Machine Systems Bottom Guard
3512C Engine for Caterpillar Built Machines Engine Oil Pressure Sensor - Remove and Install
950H and 962H Wheel Loaders Electrohydraulic System Pressure Sensor
IT38H Integrated Toolcarrier and 938H Wheel Loader Braking and Hydraulic Fan System Gear Motor (Hydraulic Fan)
2008/04/14 An Improved Pressure Switch For The Secondary Steering Attachment is Now Available {1435}
D7E Track-Type Tractor Hydraulic, HVAC, and Electrical Systems Piston Pump (Steering) - Test and Adjust
D6N Track-Type Tractor Monitoring System Diagnostic Code List
3406C Engines for Caterpillar Built Machines Fuel Filter Base
D7E Track-Type Tractor Machine Systems Refrigerant Compressor - Remove and Install
D7E Track-Type Tractor Hydraulic, HVAC, and Electrical Systems Ground Fault Detection
980H Wheel Loader Power Train Transmission Hydraulic Control