Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7574 | Link Brackets | 2 |
Start By:
- Remove the hood. Refer to Disassembly and Assembly , " Hood - Remove".
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
- Drain the hydraulic tank into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change".
Show/hide table
Illustration 1 g01445397 - Remove clip (1).
Show/hide table
Illustration 2 g01445398 - Remove clips (2).
Show/hide table
Illustration 3 g01445413 - Remove clip (3).
Show/hide table
Illustration 4 g01445415 - Disconnect harness assembly (4). Remove three cable straps (5).
Show/hide table
Illustration 5 g01445421 - Remove bolts (6). Remove rail (7).
Show/hide table
Illustration 6 g01445435 - Remove clip (8).
Show/hide table
Illustration 7 g01445440 - Remove clips (9).
Show/hide table
Illustration 8 g01445474 - Remove bolts (10). Remove rail (11).
Show/hide table
Illustration 9 g01445490 - Disconnect harness assembly (12). Remove clip (13).
Show/hide table
Illustration 10 g01445491 - Disconnect harness assembly (14).
Show/hide table
Illustration 11 g01445573 - Disconnect harness assembly (15). Remove clip (16).
Show/hide table
Illustration 12 g01445574 - Remove clip (19). Loosen clamp (17). Disconnect hose assembly (18).
Show/hide table
Illustration 13 g01445575 - Disconnect hose assemblies (20). Remove clips (21).
Show/hide table
Illustration 14 g01445577 - Disconnect hose assembly (22). Remove clip (23).
Show/hide table
Illustration 15 g01445583 - Remove clip (24).
Show/hide table
Illustration 16 g01445584 - Remove bolts (26). Remove cover (25).
Show/hide table
Illustration 17 g01445585 - Disconnect harness assembly (27). Remove clips (28). Disconnect tube assembly (29).
Show/hide table
Illustration 18 g01445749 - Disconnect hose assemblies (31). Disconnect tube assembly (30).
Show/hide table
Illustration 19 g01445752 - Disconnect hose assemblies (34). Remove tee assembly (33). Position tee assembly (33) and the block out of the way. Remove bracket (32).
Show/hide table
Illustration 20 g01445753 - Disconnect hose assemblies (35).
Show/hide table
Illustration 21 g01445754 - Disconnect hose assemblies (36). Remove clip (37).
Show/hide table
Illustration 22 g01445758 - Remove panel (38). Repeat for opposite side.
Show/hide table
Illustration 23 g01445761 - Remove bracket (39).
Show/hide table
Illustration 24 g01445762 - Disconnect hose assembly (40) from below the engine.
Show/hide table
Illustration 25 g01445766 Show/hide tableIllustration 26 g01445767 - Attach Tooling (A) and a suitable lifting device to hydraulic tank (41). The weight of hydraulic tank (41) is approximately
1043 kg (2300 lb) . - Remove bolts (42) and (43). Remove hydraulic tank (41).
Show/hide table
Illustration 27 g01446111 - Disconnect harness assemblies (44). Disconnect tube assemblies (45). Remove fuel filter assemblies (46).
Show/hide table
Illustration 28 g01446006 - Drain sediment bowl (50). Disconnect hose assemblies (48). Disconnect harness assemblies (49). Remove the fuel filter and priming pump (47).