MID 082 - CID 0084 - FMI 04
产生此代码的情况:
Show/hide table
图 1 | g01622912 |
"行驶速度"传感器示意图 |
机具 ECM 检测到来自传感器(导线 C913-BU)的信号对接地短路后会记录该诊断代码。 位置传感器会产生一个 PWM 信号。 传感器信号线 (C913-BU) 连接在机具 ECM 触针 J2-43 上。
该诊断代码可能的原因如下:
- 传感器电源电路(导线 116-BR)对高电压短路。
- 信号电路(导线 C913-BU) 对接地短路。
- 传感器出故障。
- ECM 存在故障。 但这种可能性很小。
注: 确保 CID 0084 FMI 04 处于现行状态。 此步骤可能会导致生成新的诊断代码。 可忽略生成的这些诊断代码。 完成测试步骤后,清除生成的诊断代码。
测试步骤 1. 检查传感器。
- 将断路开关和钥匙起动开关转到 ON(接通)位置。
- 确保该诊断代码为现行状态。
- 观测该诊断代码的状态。 从机器线束上断开传感器。
预期结果:
如果传感器不是引起该诊断代码的原因,该诊断代码将仍为现行状态。 如果该诊断代码不再处于现行状态,则传感器是引发该诊断代码的原因。
结果:
- 正常 - 该诊断代码仍为现行状态。 传感器无故障。 可能是机器线束或 ECM 有故障。 转至测试步骤 2。
- 异常 - 该诊断代码不再为现行状态。 机器线束和 ECM 工作正常。
修复: 传感器有故障。 更换传感器并执行提升油缸位置传感器的标定步骤。 请参考您的机器的维修手册中的测试和调整, "标定"步骤。 确认使用新传感器后故障得到排除。 如果仍存在该故障,则需先退出本步骤,然后重新执行一次。
停止
测试步骤 2. 检查信号电路是否对接地短路。
- 传感器仍保持与机器线束断开的状态。
- 将钥匙起动开关和断路开关转到 OFF(断开)位置。
- 从 ECM 上断开 J2 机器线束接头。
- 在机器线束接头 J1 上,测量触针 J2-43(导线 C913-BU)与接地之间的电阻。
预期结果:
电阻大于 5000 欧姆。
结果:
- 正常 - 电阻大于 5000 欧姆。
修复: ECM 出故障的可能性非常小。 退出并重新执行本测试步骤。 如果没有找到产生该诊断代码的原因,则应更换 ECM。 请参考故障诊断与排除, "电子控制模块 (ECM) - 更换"。
停止
- 异常 - 电阻小于 5000 欧姆。
修复: 机器线束有故障。 机器线束中信号电路与接地之间短路。 修理或更换机器线束。
停止
Caterpillar Information System:
Bench Test Procedure for a 621E, 621F, 621G, 621S, 623E, 623F, 623G, 627E, 627F and 627G Wheel Tractor Transmission{3030, 3073} Bench Test Procedure for a 621E, 621F, 621G, 621S, 623E, 623F, 623G, 627E, 627F and 627G Wheel Tractor Transmission{3030, 3073}
AccuGrade® GPS (CD700) Configuration - Machine Radio
AccuGrade® GPS (CD700) Configuration - Receiver
D8T, D9T, D10T and D11T Track-Type Tractors MID 082 - CID 0084 - FMI 03
Reuse and Salvage for Camshafts {1210, 1210} Reuse and Salvage for Camshafts {1210, 1210}
D8T, D9T, D10T and D11T Track-Type Tractors Auto Carry System
993K Wheel Loader Braking System Parking Brake - Test
993K Wheel Loader Power Train Output Transfer Gears
993K Wheel Loader Braking System Service Brake System Pressure - Test
992K Wheel Loader Machine Systems Piston Pump (Implement, RH) - Assemble
992K Wheel Loader Machine Systems Piston Pump (Implement, RH) - Disassemble
992K Wheel Loader Machine Systems Piston Pump (Implement, RH) - Remove
D8T, D9T, D10T and D11T Track-Type Tractors MID 082 - CID 0084 - FMI 08
854K Wheel Dozer Machine Systems Gear Pump (Implement Pilot) - Disassemble
854K Wheel Dozer Machine Systems Gear Pump (Implement Pilot) - Assemble
854K Wheel Dozer Machine Systems Gear Pump (Steering Oil Cooler) (Steering Pilot) - Disassemble
854K Wheel Dozer Machine Systems Gear Pump (Steering Oil Cooler) (Steering Pilot) - Assemble
Procedure to install 315-6321, 315-6323 Coupler Lines Group on Certain Wheel Loaders {5057, 6129} Procedure to install 315-6321, 315-6323 Coupler Lines Group on Certain Wheel Loaders {5057, 6129}
993K Wheel Loader Lifting and Tying Down the Machine
994F Wheel Loader Machine Systems Grease Tank (Automatic Lubrication) - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Pump - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injector - Remove and Install