Fuel Injection Lines - Remove and Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
Show/hide table
注意 |
---|
松开或拧紧燃油管时,不要让喷油器顶部转动。 如果喷油器顶部在喷油器体中转动,可能会损坏喷油器。 如果使用有缺陷的喷油器,由于从喷嘴喷出的喷油形状不正确,将会对发动机造成损害。 |
注: 在所有管组件上标出识别标记,以方便安装。 塞住所有的管路和管组件,以防止受到污染。
- 将燃油供应转到断开位置。
Show/hide table
图 1 g01326550 典型示例 - 从喷油器上断开喷油管 (2) 的螺母 (1)。
- 从喷油泵上断开喷油管 (2) 的螺母 (1)。
- 将喷油管 (2) 作为一个整体从发动机上拆下。
- 立即使用合适的盖塞住喷油泵的开口。
- 该发动机有一个刚性回油管。
将中空螺栓 (4) 从回油管 (3) 上拆下。 拆下垫圈 (8)。
Show/hide table图 2 g01326555 典型示例 - 将螺母 (5) 从喷油器 (7) 上拆下。
注: 对于配有刚性回油管的发动机,确保拧松螺母时回油管未变形。
- 将回油管 (3) 和垫圈 (6) 从喷油器 (7) 上拆下。
- 立刻使用合适的盖塞住喷油器。
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件名称 | 数量 |
A | 276-1216 | 喷射器管螺母工具 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
松开或拧紧燃油管时,不要让喷油器顶部转动。 如果喷油器顶部在喷油器体中转动,可能会损坏喷油器。 如果使用有缺陷的喷油器,由于从喷嘴喷出的喷油形状不正确,将会对发动机造成损害。 |
注: 三缸发动机和四缸发动机的安装步骤相似。
- 从喷油器 (7) 上拆下盖。 将新垫圈 (6) 和回油管 (3) 安装到喷油器 (7) 上。
注: 垫圈 (6) 带有两个小孔。
- 将螺母 (5) 安装到喷油器 (7) 上。
- 该发动机有一个刚性回油管。
将新垫圈 (8) 安装到回油管 (3) 上,然后将中空螺栓 (4) 安装到喷油泵上。 将中空螺栓 (4) 拧紧至扭矩为
7 N·m (62 lb in) 。 - 拧紧螺母 (5) 至扭矩为
27 N·m (20 lb ft) 。Show/hide table图 4 g01326550 典型示例 - 拆下喷油泵出口接头上的盖。 将喷油管作为一个整体安装到发动机上。
- 连接喷油器 (7) 上的喷油管 (2)。 紧固管接螺母 (1) 并用手拧紧。
- 使用工具 (A) 拧紧喷油泵处的管接螺母 (1)。
将管接螺母 (1) 拧紧至扭矩为
23 N·m (17 lb ft) 。注: 首先拧紧中间的管接螺母。
- 使用工具 (A) 拧紧喷油器处的管接螺母 (1)。
将管接螺母 (1) 拧紧至扭矩为
23 N·m (17 lb ft) 。 - 将燃油供应转到接通位置。
- 充注燃油系统。 有关更多信息,请参阅操作和保养手册, "燃油系统 - 充油"。
Show/hide table
图 3 | g01326555 |
典型示例 |
Caterpillar Information System:
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
994F Wheel Loader Machine Systems Grease Tank (Automatic Lubrication) - Install
993K Wheel Loader Lifting and Tying Down the Machine
Procedure to install 315-6321, 315-6323 Coupler Lines Group on Certain Wheel Loaders {5057, 6129} Procedure to install 315-6321, 315-6323 Coupler Lines Group on Certain Wheel Loaders {5057, 6129}
854K Wheel Dozer Machine Systems Gear Pump (Steering Oil Cooler) (Steering Pilot) - Assemble
854K Wheel Dozer Machine Systems Gear Pump (Steering Oil Cooler) (Steering Pilot) - Disassemble
854K Wheel Dozer Machine Systems Gear Pump (Implement Pilot) - Assemble
854K Wheel Dozer Machine Systems Gear Pump (Implement Pilot) - Disassemble
D8T, D9T, D10T and D11T Track-Type Tractors MID 082 - CID 0084 - FMI 08
D8T, D9T, D10T and D11T Track-Type Tractors MID 082 - CID 0084 - FMI 04
Bench Test Procedure for a 621E, 621F, 621G, 621S, 623E, 623F, 623G, 627E, 627F and 627G Wheel Tractor Transmission{3030, 3073} Bench Test Procedure for a 621E, 621F, 621G, 621S, 623E, 623F, 623G, 627E, 627F and 627G Wheel Tractor Transmission{3030, 3073}
AccuGrade® GPS (CD700) Configuration - Machine Radio
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Pump - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injector - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Line - Remove and Install
D11R Track-Type Tractor Hydraulic System Bulldozer Dual Tilt Cylinder
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Water Pump - Remove and Install - C1.5 and C2.2 Engines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel - Install