Engine Oil Line - Remove and Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 松开将机油管 (1) 上的夹子固定到喷油泵上的螺母 (2)。
- 拆下中空螺栓 (3),然后从缸体上拆下垫圈 (4)。
Show/hide table
图 2 g01307372 典型示例 - 拆下中空螺栓 (5),然后从缸盖上拆下垫圈 (6)。
- 从发动机上拆下机油管 (1)。
Show/hide table
图 1 | g01304820 |
典型示例 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 将机油管 (1) 放到发动机上。 确保机油管上的夹子位于螺母 (2) 下方。
- 将中空螺栓 (3) 和新的垫圈 (4) 置于机油管 (1) 上。 将中空螺栓和机油管安装到缸体上并用手拧紧。
Show/hide table
图 4 g01307372 典型示例 - 将中空螺栓 (5) 和新的垫圈 (6) 置于机油管 (1) 上。 将中空螺栓和机油管安装到缸盖上并用手拧紧。
- 将螺母 (2) 拧紧至扭矩
15 N·m (133 lb in) ,该螺母将机油管 (1) 上的夹子固定到喷油泵上。 - 拧紧中空螺栓 (3) 和 (5) 至扭矩为
12 N·m (106 lb in) 。
Show/hide table
图 3 | g01304820 |
典型示例 |
Caterpillar Information System:
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injector - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Pump - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
994F Wheel Loader Machine Systems Grease Tank (Automatic Lubrication) - Install
993K Wheel Loader Lifting and Tying Down the Machine
Procedure to install 315-6321, 315-6323 Coupler Lines Group on Certain Wheel Loaders {5057, 6129} Procedure to install 315-6321, 315-6323 Coupler Lines Group on Certain Wheel Loaders {5057, 6129}
854K Wheel Dozer Machine Systems Gear Pump (Steering Oil Cooler) (Steering Pilot) - Assemble
854K Wheel Dozer Machine Systems Gear Pump (Steering Oil Cooler) (Steering Pilot) - Disassemble
D11R Track-Type Tractor Hydraulic System Bulldozer Dual Tilt Cylinder
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Water Pump - Remove and Install - C1.5 and C2.2 Engines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
2007/12/10 The Use of Two Reusability Guidelines is Not Recommended {3101}
950H, 962H, 966H, 972H Wheel Loaders and IT62H Integrated Toolcarrier Lift Cylinder Rod Ends May Create a Void{5102} 950H, 962H, 966H, 972H Wheel Loaders and IT62H Integrated Toolcarrier Lift Cylinder Rod Ends May Create a Void{5102}
AD55B Underground Articulated Truck Braking System Brake Control Valve (Service)
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Basic Engine