Auxiliary Water Pump - Disassemble
Disassembly Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-1855     | Retaining Ring Pliers     | 1     |
B     | 1P-1861     | Retaining Ring Pliers     | 1     |
C     | 1P-0510     | Driver Group     | 1     |
D     | 9S-9152     | Bearing Puller     | 1     |
E     | -     | Guide Bolt 3/4 - 16 x 4 inch     |
1     |
Start By:
- Remove the auxiliary water pump. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Remove nut (1) .
Show/hide table
Illustration 1 | g01088086 |
- Remove gear (2) .
- Remove bolts (3). Remove mounting plate (4) .
- Remove lip seal (5) from mounting plate (4) .
Show/hide table
Illustration 2 | g00653096 |
- Remove bolts (6). Remove cover plate (7) .
Show/hide table
Illustration 3 | g00653078 |
- Use Tooling (E) to drive pump impeller (8) off the water pump shaft.
Show/hide table
Illustration 4 | g01081314 |
- Remove the key from the water pump shaft.
- Remove O-ring seal (9) .
Show/hide table
Illustration 5 | g00653188 |
- Remove bolt (10), the O-ring seal, and cam (11) .
- Remove plate (12). Inspect locator pin (13) .
Show/hide table
Illustration 6 | g00653156 |
- Use Tooling (A) to remove retaining ring (14) .
Show/hide table
Illustration 7 | g00653542 |
- Use Tooling (B) to remove retaining ring (15) .
Show/hide table
Illustration 8 | g00653549 |
- Use a suitable press to press shaft (16) out of the water pump housing from the impeller end of the water pump housing.
Show/hide table
Illustration 9 | g00653563 |
- Use Tooling (C) to remove the seal assembly.
- Use Tooling (A) to remove retaining rings (17). Remove washers (18) .
Show/hide table
Illustration 10 | g00653570 |
- Use Tooling (D) and a suitable press to remove bearings (19) and spacer (20) .
Show/hide table
Illustration 11 | g00653154 |
Caterpillar Information System:
2006/01/23 Installation of a Jacket Water Heater Reduces the Formation of Condensation {1383}
C6.6 Generator Set Indicator Lamps
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines Sensors and Electrical Connectors
2006/01/23 Changes to Specifications "Piston and Rings" {1214, 1215}
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump
G3500 A3 Engines Self-Diagnostics
C6.6 Engines for Caterpillar Built Machines Glow Plugs
2006/03/20 A New Exhaust Gasket is Now Available {1059}
3126B and 3126E Truck Engines Inlet Air Temperature Sensor
C6.6 Engines for Caterpillar Built Machines Speed Sensor
C6.6 Engines for Caterpillar Built Machines Inlet Manifold Temperature Sensor
C15 Petroleum Generator Set Engines Inlet Manifold Air Pressure Sensor
C6.6 Engines for Caterpillar Built Machines Engine Oil Pan
Check Engine Light ON with No Active Fault Codes for 3126E Engines{1901, 1902, 7431, 7620} Check Engine Light ON with No Active Fault Codes for 3126E Engines{1901, 1902, 7431, 7620}
3126B and 3126E Truck Engines Electronic Control Wiring Group
CX31 On-Highway Transmission Transmission Control
CX31 On-Highway Transmission Transmission Warm-up
CX31 On-Highway Transmission Transmission Oil - Change
CX31 On-Highway Transmission Transmission Oil Level - Check
CX31 On-Highway Transmission Transmission Oil Sample - Obtain
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission Shifting Function
2010/09/01 Cylinder Pack Upgrade Is Available for Certain 3406B and 3406C Engines When Replacing All Six Cylinders Packs {1201, 1225}
Oil Pan and Gasket{1302, 1302} Oil Pan and Gasket{1302, 1302}
C15 and C18 Generator Set Engines Turbocharger - Disassemble