IT38H Integrated Toolcarrier and 938H Wheel Loader Engine Supplement Caterpillar


Gear Motor (Hydraulic Fan) - Assemble

Usage:

938H JKM

Assembly Procedure

Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     1P-1858     Retaining Ring Pliers     1    
B     1U-8846     Gasket Sealant     1    

Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.




    Illustration 1g01175672



    Illustration 2g01175541

  1. Install backup seals (17) and seal (16) on plate (15) .

  1. Install plate (15) .



    Illustration 3g01175540

  1. Install gear (14) and shaft (13) in body (5) .



    Illustration 4g01175539



    Illustration 5g01175538

  1. Install backup seals (12) and seal (11) on plate (10) .

  1. Install plate (10) .



    Illustration 6g01175536

  1. Install O-ring seal (9) on flange (77) .



    Illustration 7g01175534

  1. Install seal (8) .



    Illustration 8g01175533

  1. Install flange (7) . Reposition the gear motor and use Tooling (A) to install retaining ring (6) .



    Illustration 9g01175532

  1. Install O-ring seals (4) to body (5) .



    Illustration 10g01175531

  1. Remove plug (1) and the O-ring seal.

  1. Install cover (3) and bolts (2) .

End By: Install the gear motor for the hydraulic fan. Refer to Disassembly and Assembly, "Gear Motor (Hydraulic Fan) - Install".

Caterpillar Information System:

816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1406 - FMI 13
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1405 - FMI 13
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1404 - FMI 13
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1403 - FMI 13
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1402 - FMI 13
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer MID 081 - CID 1401 - FMI 13
953D Track-Type Loader Hydraulic System Piston Pump (Implement)
D6T Track-Type Tractor Hydraulic System General Information
IT38H Integrated Toolcarrier and 938H Wheel Loader Engine Supplement Gear Motor (Hydraulic Fan) - Disassemble
IT38H Integrated Toolcarrier and 938H Wheel Loader Engine Supplement Fan and Gear Motor (Hydraulic Fan) - Install
2007/03/12 Maintenance Instruction Has Been Added for HMU Steering {4310, 4343}
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Engine Top Speed Is Not Obtained
Increase the Service Life of the Elevator Chain Idler on Certain Wheel Tractor-Scrapers{6241} Increase the Service Life of the Elevator Chain Idler on Certain Wheel Tractor-Scrapers{6241}
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Acceleration Is Poor or Throttle Response Is Poor
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Engine Overspeeds
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Engine Misfires, Runs Rough or Is Unstable
Installation Instructions for the 2Q-8720 Machine Performance Gp (Fuel Management System) (Kit) for the 988H{1052, 3101} Installation Instructions for the 2Q-8720 Machine Performance Gp (Fuel Management System) (Kit) for the 988H{1052, 3101}
C15 and C18 Petrolem Generator Set Engines Engine Stalls at Low RPM
C9 Engine for the 816F Series 2 Landfill Compactor, the 815F Series 2 Soil Compactor, and the 814F Series 2 Wheel Dozer Throttle Lock - Test
2007/01/29 Improvements to the Mounting Plates of the Tilt Cylinders {5104}
3524B Engines for 797 and 797B Off-Highway Trucks Checking Engine Cylinders
259D, 279D, 289D, 299D and 299D XHP Compact Track Loaders, 257D, 277D, 287D, 297D and 297D XHP Multi Terrain Loaders and 236D, 242D, 246D, 262D, 272D and 272D XHP Skid Steer Loaders Machine Systems Fuel Tank - Remove and Install
2008/08/11 Improved Oil Pressure Senders Are Now Available {1924}
IT38H Integrated Toolcarrier and 938H Wheel Loader Machine Systems Pilot Oil Accumulator (Dead Engine, Lift Arm Lower) - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.