Torque Converter - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 3     |
B     | 8T-0276     | 螺栓     | 2     |
C     | 1P-0520     | 冲头总成     | 1     |
D     | 154-6181     | 顶出螺钉     | 2     |
开始:
- 拆下变矩器。 请参阅拆解和组装, "变矩器 - 拆卸"。
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
- 将工具 (A) 和适当的起吊设备连接到变矩器 (1) 上。 变矩器 (1) 的重量约为 125 kg (275 lb)。 将变矩器 (1) 置于适当的支座上。
Show/hide table
图 1 | g01230093 |
- 拆下螺栓 (2) 和板组件 (3) 。
Show/hide table
图 2 | g01230097 |
- 卸下螺栓 (4) 。 使用工具 (B) 拆下先导阀 (5) 。
Show/hide table
图 3 | g01230098 |
- 卸下护圈 (6) 。 拆下 O 型密封圈 (7) 。
Show/hide table
图 4 | g01230100 |
- 从挡圈 (6) 上拆下环 (8) 。
Show/hide table
图 5 | g01230101 |
- 拆下 O 型密封圈 (9) 。 将工具 (A) 和适当的起吊设备连接到壳体组件 (10) 。 壳体组件 (10) 的重量约为 34 kg (75 lb)。 拆下螺栓 (11) 和壳体组件 (10) 。
Show/hide table
图 6 | g01230102 |
- 拆下环 (13) 。 利用工具 (C) 拆下轴承 (12) 。
Show/hide table
图 7 | g01230103 |
- 从活塞 (15) 上拆卸环 (14) 。 拆下活塞 (15) 。 拆下 O 形密封圈 (16) 。
Show/hide table
图 8 | g01230104 |
- 拆下螺栓 (17) 、接头组件 (18) 和座圈 (19) 。
Show/hide table
图 9 | g01230105 |
- 拆下板和盘 (20) 。 拆下轴承 (21) 。
注: 为便于安装,标记板和盘 (20) 的顺序。
Show/hide table
图 10 | g01230106 |
- 使用工具 (D) 拆下板 (22) 。
Show/hide table
图 11 | g01230107 |
- 拆下 O 型密封圈 (23) 。 拆下座圈 (24) 。 使用工具 (D) 拆下板 (25) 。
Show/hide table
图 12 | g01230110 |
- 从叶轮 (26) 上拆卸定位销 (27) 和 O 形密封圈 (28) 。 拆卸涡轮 (29) 。
Show/hide table
图 13 | g01230111 |
- 拆下轮毂 (30) 。
Show/hide table
图 14 | g01230135 |
- 拆下座圈 (31) 。
Show/hide table
图 15 | g01230136 |
- 拆下轴承 (32) 。
Show/hide table
图 16 | g01230137 |
- 由两名人员重新安装叶轮 (26) 。 叶轮 (26) 的重量约为 31 kg (70 lb)。 拆下挡圈 (34) 。 从托架 (33) 上拆下叶轮 (26) 。
注: 拆下挡圈 (34) 前,确保支撑托架 (33) 。
Show/hide table
图 17 | g01230138 |
- 从适配器 (38) (未显示)上拆下座圈 (35) 、螺栓 (36) 和叶轮 (26) 。 拆下轮毂 (37) 。
Show/hide table
图 18 | g01230139 |
- 从适配器 (38) 上卸下 O 形密封圈 (39) 。
Show/hide table
图 19 | g01230140 |
- 拆下轴承 (40) 。 从定子 (41) 上拆下托架 (33) 。
Show/hide table
图 20 | g01230141 |
- 拆下轴承 (42) 、滚柱 (43) 和弹簧 (44) 。 拆下挡圈 (45) 和板 (46) 。
Show/hide table
图 21 | g01230142 |
- 重新定位定子 (41) 。 拆下挡圈 (47) 和板 (48) 。
Show/hide table
图 22 | g01230143 |
- 使用适当的压具和工具 (C) 从定子 (41) 上拆下凸轮 (49) 。 拆卸凸轮 (49) ,然后拆卸挡圈 (50) 。
注: 为便于组装,标记凸轮的方位。
Show/hide table
图 23 | g01230145 |
Show/hide table
图 24 | g01230955 |
Caterpillar Information System:
C3.3 Industrial Engine Crankcase Breather - Remove and Install
C3.3 Industrial Engine Gear Group (Front) - Install
C3.3 Industrial Engine Gear Group (Front) - Remove
C3.3 Industrial Engine Valve Mechanism Cover - Remove and Install
C3.3 Industrial Engine Crankshaft Pulley - Remove and Install
C3.3 Industrial Engine Crankshaft Front Seal - Remove
2006/01/02 A New Water Pump is Now Used {1361}
3500B Engines Radiator Core - Install
3500B Engines Radiator Core - Remove
CX31 On-Highway Transmission Power Train Transmission and Torque Converter - Connect
CX31 On-Highway Transmission Power Train Transmission and Torque Converter - Separate
3512B Oil Well Servicing Engine (ADEM III) Starting Motor System
CX31 On-Highway Transmission Power Train Torque Converter - Assemble
C3.3 Industrial Engine Rocker Shaft and Pushrod - Remove
C3.3 Industrial Engine Rocker Shaft and Pushrod - Install
C3.3 Industrial Engine Cylinder Head - Remove
C3.3 Industrial Engine Cylinder Head - Install
C6.6 Engines for Caterpillar Built Machines Fuel Transfer Pump
C7 and C9 Marine Engines Replacing the ECM
3126B Engine for Caterpillar Built Machines Mechanical Noise (Knock) in Engine
3126B and 3126E Truck Engines Piston and Rings
3126B and 3126E Truck Engines Piston and Rings
Application and Installation Guide for Oil/Gas Well Servicing Transmissions and Oil/Gas Well Servicing Power Systems (Mechanical Guide){1408, 1435, 3030, 3101, 7553} Application and Installation Guide for Oil/Gas Well Servicing Transmissions and Oil/Gas Well Servicing Power Systems (Mechanical Guide){1408, 1435, 3030, 3101, 7553}
C6.6 Generator Set CID 0261 FMI 11